4W71D Starting/running issues

Houdini_1980

Recruit
Thread starter
Joined
Jul 20, 2017
Messages
2
Hey guys. First post here. Got some info on setting up the carb on this 4W71D that I had given to me. Was told it ran good at high speed but wouldn't idle. Hasn't been run in almost 10 years. Cleaned it up, rebuilt the carb, does not have cork float. Replaced the impeller and spark plugs and tried setting the carb. Had a heck of a time at first. Realized there was fuel/oil in my test tank and it was only firing on one cylinder. Both coil housings were cracked and arking on the flywheel. Replaced coils and condensers. I haven't replaced the points yet as they are nice and clean looking, but I do have them. (Just a little background... I'm an automotive mechanic, 20 years total experience but a little new to 2 strokes.) After that repair, I had it running great in the test tank. Took it out for a spin on the lake and it would not start... :facepalm:

I just took it apart again tonight as I thought the float had stuck a bit as there was fuel coming out the front of the carb. Carb and float look good, moving freely, bulb gets solid when pumping it up. I pulled the spark plugs and they were dry. I had good spark so whatever fuel was getting into the cylinder was being burnt. I also checked to see if I had compression and vacuum with the plugs out. I indeed had both. I had it running briefly with the last pull of the rope as it broke off, but it died after about 5 seconds of running. I am going to bring my spark tester home this weekend just to make sure I have a good strong spark, but I think it may be a fuel issue. Any other ideas would be welcome.

Thanks for any info guys!
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
I don't know what is wrong with your motor, but just a couple of comments. Those motors are a bit tricky to start because you can't tell where you have the throttle set. If not high enough to crack the carburetor shaft open a bit, it will be hard to start. Gas/oil in the test tank is not very meaningful. A brand new motor will produce some gas/oil in the tank. Having spark does not mean that fuel in the cylinders is being burnt. It has to be the right amount of fuel---that is a burnable fuel/air ratio. Too much gas won't burn (flooded). It also needs enough compression---around 80 psi is normal on that motor. Fuel coming out the front of the carb might mean a stuck or leaking float valve, or overly mashing on the primer bulb, or over choking, or the motor tilted up some (have it sitting level). Finally, that starter rope. I realize you were frustrated, but those starters defy all the normal rules. Give it short, forceful yanks with your palm up. That will discourage pulling it all the way to the end and breaking it.
 

Houdini_1980

Recruit
Thread starter
Joined
Jul 20, 2017
Messages
2
Thanks for the reply F_R. The reason the rope broke is I released it too quick a few times and it got stuck and frayed the rope, finally breaking it. I'm not too concerned with that as I have a spool of starter rope and it's easy enough to replace.

An update...

I finally had the chance to check for spark and I have no spark on #2 (lower cylinder). Does anyone know which coil is which before I start ripping it apart fully? I'm going to replace and set up the points, as I do have new ones waiting to go in, but would like to be sure which coil is the issue first.

Thanks.
 

Crosbyman

Admiral
Joined
Nov 5, 2006
Messages
6,298
FRONT COIL = TOP CYL


YOU NEED TO PULL THE FLYWHEEL AND DO ALL THE ELECTRICALS ANYWAY TO BE CONFIDENT. THESE ARE EXCELLENT MOTOR AND WILL TROLL ALL DAY LONG FOR YOU IF YOU TAKE CARE OF IT

​THE 3HP AND 4 HP ARE VERY SIMILAR (SORRY FOR CAPS LOCK ) DON<T WANT TO RETYPE ALL THIS

http://www.outboard-boat-motor-repair.com/Evinrude 3 HP Lightwin Outboard Boat M otor/Evinrude%20Johnson%203%20HP%201952-1967%20Ignition%20System%20Tune-up.htm

http://www.maxrules.com/fixtuneitup.html


http://www.outboard-boat-motor-repair.com/motors/Evinrude 4 HP 1971 Model 4106 4136

​
 
Top