Hi, my first post here. Running into trouble with my 1969 Evinrude 25 hp. Here is the deal. Last fall, I had what was a suspected worn clutch dog. (I can't get the gearcase apart to check because there is a nasty stripped screw). The motor would jump out of forward and wind out at high rpms. It got worse and worse on one trip and had to use the trolling motor to get back to the dock. A few weeks later I found a 74 Johnson 25 hp, and picked that up thinking I could use that motor if it was better or harvest it for parts.
Turns out the Evinrude had better compression, so I focused on that motor. I put the lower from the Johnson on the Evinrude and everything seemed to be in order, once I got the shift linkage lined up to where I think it was supposed to be. I ran it in a barrel. No problems. Took it to the river and ran it there, no problems, but I couldn't open it up to more than about 3/4s throttle because of the narrow width of the river. Took it to the lake and almost right away, it was popping out of forward again just like it did in the fall, and before I even made it to 1/2 throttle. I also noticed that the water pump, which had been working at the dock, was now not working.
Once I got home and took the lower off again and got into the water pump, I noticed the impeller pin in the drive shaft was sheared off. I had another pin from the other motor and replaced that pin. I looked everything over and made some additional adjustments to the shift linkage and ran it in the barrel again. Worked fine at first. Shifted great. Did not hear any grinding or revving or any popping out of gear. BUT....it stopped spitting water after a few minutes and after I started testing the shifter. I once again dropped the lower and got into the water pump. The impeller pin was again broken and in the same spot.
So, I was wondering if I needed a new impeller and I definitely needed a new pin. So I ordered an impeller kit and put in a new impeller and pin, reassembled everything, making some adjustments to the linkage and the two screws in the shift handle in order to make sure everything was tight, and ran it in a barrel. No problems. Water flow was great. Shifted great. No issues. I took it to the lake and at first everything ran great. Pumping good. Shifting good. When I got up to about 3/4's throttle again, the motor lurched slightly a couple times but otherwise was staying in gear. Then I noticed the water pump was not working.
I have not taken it apart again to check, but my guess is that impeller pin is broken again.
Anyone have any thoughts on what my next step should be, other than giving up and parting out both motors?
Turns out the Evinrude had better compression, so I focused on that motor. I put the lower from the Johnson on the Evinrude and everything seemed to be in order, once I got the shift linkage lined up to where I think it was supposed to be. I ran it in a barrel. No problems. Took it to the river and ran it there, no problems, but I couldn't open it up to more than about 3/4s throttle because of the narrow width of the river. Took it to the lake and almost right away, it was popping out of forward again just like it did in the fall, and before I even made it to 1/2 throttle. I also noticed that the water pump, which had been working at the dock, was now not working.
Once I got home and took the lower off again and got into the water pump, I noticed the impeller pin in the drive shaft was sheared off. I had another pin from the other motor and replaced that pin. I looked everything over and made some additional adjustments to the shift linkage and ran it in the barrel again. Worked fine at first. Shifted great. Did not hear any grinding or revving or any popping out of gear. BUT....it stopped spitting water after a few minutes and after I started testing the shifter. I once again dropped the lower and got into the water pump. The impeller pin was again broken and in the same spot.
So, I was wondering if I needed a new impeller and I definitely needed a new pin. So I ordered an impeller kit and put in a new impeller and pin, reassembled everything, making some adjustments to the linkage and the two screws in the shift handle in order to make sure everything was tight, and ran it in a barrel. No problems. Water flow was great. Shifted great. No issues. I took it to the lake and at first everything ran great. Pumping good. Shifting good. When I got up to about 3/4's throttle again, the motor lurched slightly a couple times but otherwise was staying in gear. Then I noticed the water pump was not working.
I have not taken it apart again to check, but my guess is that impeller pin is broken again.
Anyone have any thoughts on what my next step should be, other than giving up and parting out both motors?