2002 Johnson 175 Minimum compression needed to run VRO

hazzman

Recruit
Thread starter
Joined
Jul 14, 2016
Messages
3
I have been wrestling with my 2002 Johnson 175 for a few weeks now.
​I have been thru all of the diagnostic procedures.
My symptoms are the boat runs good at idle and mid-range but starves for fuel at higher RPM's and WOT.
If I pump the primer bulb all symptoms clear up until it uses all the primer pumped fuel again.
then after a few minutes the engine begins to misfire again due to lack of fuel.
I have decarbed the engine.
I have replaced the fuel filter.
I have inspected or replaced most of the fuel hoses associated with the VRO and fuel supply.
I have inspected the pulse limiter and checked for blockage in crank case where limiter attaches.
I have eliminated the existing fuel line to the tank and ran a new line from a remote tank with a new primer bulb.
I have rebuilt the VRO with the OMC kits.

I just completed a compression test and the results are as follows: 1- 104, 2- 105, 3- 105, 4- 104, 5- 102, 6- 95.

I know from doing the research that cyl #6 is the cyl that sends the pulse to the VRO for operation of the air pump diaphragm in the VRO.

Is it possible that 95 lbs of compression in # 6 is not enough to run the VRO efficiently?

Or should I replace the VRO with a new one?

Thanks in advance for any input or assistance.

Fish On!!

hazzman
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
Welcome to iboats
It is crankcase compression not cylinder compression that operates the pump. # 6 could be low if the crankcase isn't able to send a good air/fuel charge. #6 would also be the bottom cylinder/crankcase. The lower crankcase seal may be leaking. However you are only 9% lower. Changing it requires pulling the powerhead, so do it as a last resort. WOT requires a lot MORE fuel than say, 80% throttle. You said you replaced 'most' of the hoses associated with the VRO, which one(s) didn't you replace? Are all the hoses clamped? You ran the engine on a portable tank and still had the problem?
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Double check the pulse hose to the pump and rebuilding a VRO is iffy sometimes they work and sometimes they don't. Check the plasic housings for cracks. I don't think compression is your problem. What kind of clamps did you use on the hoses.
 

hazzman

Recruit
Thread starter
Joined
Jul 14, 2016
Messages
3
yes, I eliminated the on-board fuel line completely, still had the problem.

I checked all the fuel lines, all had clamps or zip ties and all were tight.

I'm aware its crank case compression/pulses that actuate the air motor (diaphragm) in the VRO.

Is there a method for checking the pulse intensity at the limiter?

I am starting to lean towards buying a new fuel pump but I'd like to know for sure that the motor is OK first.

I'm also inclined to think that the compression in # 6 (95 lb) should be enough to generate enough of a pulse to make the fuel pump work no?
 

hazzman

Recruit
Thread starter
Joined
Jul 14, 2016
Messages
3
I used the original spring clamps, they seemed as if they were still in good shape.
I did inspect the hose from the pulse limiter to the pump and it seemed OK, I have a new one I just received from I-boats. I also have a new pulse limiter.
I'm going to install them, I was just waiting to get some input as to whether the motor is still OK before I order a new fuel pump and then do all of the work at one time.
 

ricohman

Lieutenant Commander
Joined
Jul 30, 2011
Messages
1,631
I think your compression numbers are low. My old 90 had 125 or so.
How many hours on this motor?
Still I don't think low compression is the culprit. Have you pulled the carbs and made certain the high speed circuits are clean? Running lean is no good.
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
Have you tried using a clear fuel line to see if there's air in the line? A section of it before and after the fuel pump will let you know if there's air.
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
I think your compression numbers are low. My old 90 had 125 or so.
How many hours on this motor?
Still I don't think low compression is the culprit. Have you pulled the carbs and made certain the high speed circuits are clean? Running lean is no good.


Compression for the V6s is not that high right around 100 PSI for those is good. Your motor sounds like it is healthy compression wise. The fact it runs good when you pump the ball leads to fuel issues. What about the pulse line itself does it have any cracks or breaks? Also put the clear line in and look for air bubbles like you were told. Is the pump itself in good condition one screw overtightend and it will crack.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The VRO pump is easy to take apart for inspection / repairs.--Elegantly simple unit.-----Do that before forking over the coins for a new pump.-----Have you inspected fuel lines from motor to the tank ?---Including the pick-up tube inside your tank ?----Might try a test run with a known to be good portable tank and hose too.
 
Top