2000 Johnson 50hp very low speed only... ideas?

100-31keith

Recruit
Thread starter
Joined
Mar 30, 2018
Messages
2
2000 Johnson 50hp on a 17'2" SeaArk bass boat. Less than 15 hours total use. Ran perfect back in the day and perfect the last time it was used in 2006 (yes, it has been 12 years). Inherited last month from deceased dad.

Last week, I put in 2 gallons of gas (50:1) and a relatively new battery out of one of my vehicles (temporary for the "test", lol). I also filled the oil mixer as instructed for still in break-in. Launched.

Squeezed the bulb, pushed the button in, moved the lever forward. Pumping the key, it started after the third attempt with normal high rpms. As soon as I put it in neutral, it died and did so the next two attempts.

So, with the next attempt....

As soon as I was back in neutral, I immediately put it in gear to keep it from dying. It ran, but at a very, very, very low speed (perhaps 2 or 3 times the speed of trolling with a crank bait). It was very smooth, no smoke, water pump working. I ran it for less than 2 minutes before deciding not to push it any more. The maximum speed did not vary or increase.

Could the cylinders be binding from age and non-use thus limiting the speed? Some type of fuel restriction issue (i.e. filter)? Anything else possible?

Your input will be appreciated.
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
Hey there! :welcome:

Not a pro here, but....

There used to be a thread here about "Awakening a sleeping outboard" that had great info in it for just your case..
Unfortunately, it's missing it's content at the moment..

At this point, while it may be just fine, I'd suggest you do a compression test, spark test with an adjustable open air spark gap tester (available at most auto parts stores for around 8-10 bucks). Spark gap in open air I'm not positive on, but probably somewhere around 3/8" to 7/16"..
One of the guru's I'm sure will confirm what the correct gap should be.
Spark should be crisp Blue with a definitive "SNAP!" not orange or weak.
Start with the compression and spark tests though to get a baseline of the health of the engine.

I know it has minimal hours on it, but you put gas in a went without trying to "Wake" it up first, so compression and spark will help determine if any damage was done, or better yet, rule out any damage..

Post compression numbers here, and spark test results...

Provided those results are fine, then I think it'd be time to rebuild the carbs..
Sitting that long has probably gummed up the idle circuits, high speed jets etc. in it and that's the real issue..

Once that's figured out, I'd suggest you replace the water pump impeller too.. It may have worked fine for now, but sitting that long it probably won't be ok.. Better safe than sorry..

Again, not a pro, but hopefully this gets you a start, and the seasoned folks will be along soon to help further..

Hope it helps, and Welcome again!!
 
Last edited:

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
Oh, and if you can, post the model number too.. That way we (well, the guru's anyway lol) have the specific model and can be more precise in advice :D
 

100-31keith

Recruit
Thread starter
Joined
Mar 30, 2018
Messages
2
The model number is J50VLSIB. The spark plug gap is .76 mm, .030 in.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
It was suggested to TEST your ignition system.----That test does not use the sparkplugs !-----Does the spark jump a gap of 3/8" ( 1 cm ) or more , yes or no ?----Your motor could well be running on only 1 cylinder !
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
If this motor has sat for 12 years here are a few of the steps.

drain all fuel. This includes fuel in lines and fuel pump.

remove.and clean carbs, all the orifices and passages. These are in the carb body and in the bowl as well.

remove lower. Replace impeller. It's sat for 12 years, it's junk.

drain lower . Take it to a shop and have it pressure tested. If good refill and re install.

replace plugs.

​​​​​​​go boating.
 

jbuote

Lieutenant Junior Grade
Joined
Aug 17, 2016
Messages
1,001
Yeah, the 3/8" gap I mentioned was for the open air spark tester..
Testing by looking at the removed and grounded plug will show a spark in that .030 gap, but it may not spark under compression in the cylinder.
The best way to "Simulate" spark under compression is to have a bigger gap in open air.
So, the 3/8" gap with no compression simulates the .030 gap under compression.

If it jumps the bigger gap with bright blue spark and crisp "SNAP", then it should be fine in the .030 gap under compression.
If not, then it probably won't fire in the cylinder under compression.

racerone and jakedaawg are both great sources of info and help..
Neither one (or any other pro's here for that matter) have steered me wrong yet! :D
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Hey -- Sorry about your Dad. Makes the motor special.

Got good advice. My guess would be carb cleaning (soak, poke, and spray method). Replace the impeller first, as mentioned.
 
Top