2000 70hp fuel won't go past engine fuel filter

Yupitsnuge

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
7
I have an 18' maritime skiff with a 99 johnson outboard. I haven't used the boat in about 4-5 years. Before I quit using it, I would have a hard time trolling without the motor dying and then I would have a hard time getting it started again.

I wanted to use it this year so I drained the 26gal tank, installed a new primer bulb, fuel filter immediately after primer bulb, new fuel filter on engine.

I got it started and took it for a low speed cruise to dinner. Right as we were about to pull anchor an hour or so later, the motor wouldn't start. Cranked and cranked, nada. I gave it some time and tried again, nada. Finally i got it started and hauled ass in. I figured it was dirty carbs from sitting so long. After opening them up, I would have thought they were brand new! I rebuild them anyways.

After I put them back in, I primed the bulb and noticed that as it was pumping fuel into the filter in the engine cover it would shoot right back into the fuel line. I also noticed some gunk on the bottom of the filter. It separated from the fuel. I'm assuming it was water. I replaced that filter. I also ran a new fuel hose on top of the deck just in case there was a leak under deck which was allowing water in the line. I got the primer bulb rock hard but would not push fluid into the new fuel filter in the engine case. As soon as I got about a 1/4" of fluid, it shot right back out. I removed the gas cap on the fuel tank thinking it was creating a vacuum. Still wouldn't go into the filter. I then replaced the quick disconnect thinking maybe it was that. Nope. I left the far side of the fuel filter off (fuel pump side) and pressed the bulb and it easily shot fuel out of the filter without and resistance. I also tried cranking the engine and it cranks but will not kick over.

Here's where I'm at now. It's as if there's a blockage after the fuel filter under the engine cover. What do you think is wrong with this engine?

I pulled the fuel pump out thinking I may have to rebuild it and when pulled it out, some fuel came out and then a good shot of water came out too. I opened it up and everything looks good inside.

I noticed a soft spot on floor port side right next to leaning post. Someone said I may be leaking fuel from the fuel line under deck and also absorbing water and that's why I have water in the engine fuel filter, but not on the tank side fuel filter.

Any help would be GREATLY appreciated!!
 

clemsonfor

Lieutenant Junior Grade
Joined
Sep 19, 2005
Messages
1,011
Dang I'm lost in this? Fuel not going through lines, soft spots in the floor from leaking fuel absorbing water, wate in some filters but not others??

Are the needles plugged? Pull all those inline filters off and just put the one under the motor hood on. Do you have a fuel/water seperator?
 

Yupitsnuge

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
7
Sorry, it's hard even for me to follow. I was trying to provide all the things I noticed.

I currently only have one fuel filter which is in the stock location under the hood. I cannot get fuel to go past it when fuel pump line is connected. It's almost as if there's a plug in the line. Pulled fuel pump and it looks good.

I believe water contamination was from the below deck line so I'm using a brand new above deck line.
Dang I'm lost in this? Fuel not going through lines, soft spots in the floor from leaking fuel absorbing water, wate in some filters but not others??

Are the needles plugged? Pull all those inline filters off and just put the one under the motor hood on. Do you have a fuel/water seperator?
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
If there's fuel in the carbs and the needles are closed, then you won't be able to pump fuel into the motor, it will build pressure and blow back out just like what you explained.

​Take a drain plug out of a carb and see if you can get fuel to flow
 

Yupitsnuge

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
7
No fuel in carbs at all.i just rebuild them and put them back in

If there's fuel in the carbs and the needles are closed, then you won't be able to pump fuel into the motor, it will build pressure and blow back out just like what you explained.

​Take a drain plug out of a carb and see if you can get fuel to flow
 

ondarvr

Supreme Mariner
Joined
Apr 6, 2005
Messages
11,527
Disconnect the fuel line at each point along the way and see if anything comes out, or just chuck the filter out.
 

Yupitsnuge

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
7
Yes, floats are correctly installed. Fuel gets past filter when I pull fuel pump line from it. With fuel pump line attached, it seems system is pressurized and pushes fuel back past filter. I'm thinking needles are stuck now that you said that would cause those symptoms. I'll try opening a drain valve and trying to pump it again.

Did you put the floats in right side up?
 

clemsonfor

Lieutenant Junior Grade
Joined
Sep 19, 2005
Messages
1,011
If the needles are stuck fuel will not flow into them. But if you just rebuilt them, stuck needles is not likely especially if carbs are not full of fuel thag pressure would probaly blow needles free on new rebuilt carbs. A trick is to tap the carb with a screw driver handle firmly, this can unstuck a stuck needle. But for all 3 needles to be stuck so no fuel remains in the filter would be odd.

Pull that filter out and just put a length of line. If your not comfortable for a test, put a cheap inline filter before the motor or get a fuel water seperator and mount before the engine. At that point you would no longer need the one under the hood.

They are plastic parts and possible that maybe there is a piece of flashing that was left in it and is blocking flow. Start simple and start disconnecting and removing things to rule them out. You can even pull one carb line off at the time and prime to see if fuel goes through the line allowing you to know if a needle is blocked or not.
 

Yupitsnuge

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
7
So far I've:
rebuilt carbs
Opened and cleaned fuel pump VRO

Replaced:
Everything from and including fuel quick connect back to the tank but not tank cap, that's next.

I will try pulling carb lines tonight and seeing if that does it.

If the needles are stuck fuel will not flow into them. But if you just rebuilt them, stuck needles is not likely especially if carbs are not full of fuel thag pressure would probaly blow needles free on new rebuilt carbs. A trick is to tap the carb with a screw driver handle firmly, this can unstuck a stuck needle. But for all 3 needles to be stuck so no fuel remains in the filter would be odd.

Pull that filter out and just put a length of line. If your not comfortable for a test, put a cheap inline filter before the motor or get a fuel water seperator and mount before the engine. At that point you would no longer need the one under the hood.

They are plastic parts and possible that maybe there is a piece of flashing that was left in it and is blocking flow. Start simple and start disconnecting and removing things to rule them out. You can even pull one carb line off at the time and prime to see if fuel goes through the line allowing you to know if a needle is blocked or not.
 

clemsonfor

Lieutenant Junior Grade
Joined
Sep 19, 2005
Messages
1,011
Like the one guy asked before me.

ARE YOU SURE THE FLOATS ARE IN CORRECTLY AND NOT UPSIDE DOWN?

Im not trying to yell there , but just make sure you see that question.
 

Yupitsnuge

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
7
Like the one guy asked before me.

ARE YOU SURE THE FLOATS ARE IN CORRECTLY AND NOT UPSIDE DOWN?

Im not trying to yell there , but just make sure you see that question.


Yes, floats are correctly installed. Fuel gets past filter when I pull fuel pump line from it. With fuel pump line attached, it seems system is pressurized and pushes fuel back past filter. I'm thinking needles are stuck now that you said that would cause those symptoms. I'll try opening a drain valve and trying to pump it again.

yes, floats are installed correctly.
 

Yupitsnuge

Cadet
Thread starter
Joined
Aug 13, 2017
Messages
7
Was I supposed to fill the bowls with fuel before I reinstalled them? How would fuel displace the air that's in the bowls easily? I did not try cracking the drain on them yet. Heading to boat now
 

daselbee

Commander
Joined
Jan 20, 2009
Messages
2,765
Have you been using Silverado grey replacement fuel line? Anywhere on engine? If so, it is possible that when you pushed the line onto the associated fitting, like the fuel pump for example, the inner liner of that crappy hose folded in and is creating a blockage.

That hose has a clear plastic inner liner that comes loose. Worst hose I have ever seen.

Pull the line off at the fuel pump and pump bulb. You should get steady easy fuel flow.
 
Top