1989 Evinrude 70HP VRO bogging then taking off

Kenkuniff

Cadet
Thread starter
Joined
Jul 12, 2016
Messages
7
I purchased this motor after testing compression. 119 psi on all 3 cylinders. Rebuilt carbs. Oil pump was disconnected by previous owner and plugged. Motor starts up every time after priming bulb 4-5 times. Idles very high and fast for a few seconds then comes down. Once in a while stalls but starts right back up and then idles fine. After idling for a bit at dock and then trying to go out boat bogs at full throttle for a short distance then starts to take off and bogs again the takes right off and runs fine at full throttle. However when you come off throttle and try to go again does same thing all over. After sitting for and fishing for a while hard to start even after priming but will eventually start after working choke some. Has a 14 gallon tank which I am mixing 50:1. Looking at replacing VRO pump with regular pump from Maxrules.com along with main fuel line and primer bulb. Primer bulb never gets hard. However motor does not run any better by pumping bulb while trying to get it to take off, so not sure it is the pump. Any suggestions would be appreciated.
 
Last edited:

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Sounds like a fuel delivery problem. Could be a bad hose or hose bulb, weak fuel pump, or even debris inside the carb jets. Have you had the carbs apart for a visual inspection? The primer bulb should pump up to be "hard" each time you squeeze the bulb repeatedly. (the ball valves inside the bulb do go bad over time.) Always best to have the fuel bulb oriented in a generally "upward" position. (the arrow on the hose bulb should point generally upward.) If the bulb is laying generally "downhill" in the splashwell of the boat-the bulb may not work well when it gets older.
 

Kenkuniff

Cadet
Thread starter
Joined
Jul 12, 2016
Messages
7
Thanks for the suggestions. Carb jets are good. They where taken apart and rebuilt, that was first thing I had done. This is my first boat but I have raced snowmobiles for years so the carbs are about the only thing I really know anything about. The rest is pretty foreign. I did test really quick this morning and if I hold bulb more in an upward angle then it does get hard and if I let it down it becomes soft again. Reading through the manual and looking at part schematics I noticed that there are leaf valves in this motor, do you know if they happen to go bad? and if so would they cause this sort of problem? I am ordering new fuel line, bulb, tee connectors and fuel pump. Thanks again for the suggestions.
 

Kenkuniff

Cadet
Thread starter
Joined
Jul 12, 2016
Messages
7
One other question. Was told these older motors don't do well with ethanol gas. What is your suggestions? Should I drain the gas I have and replace it with 91 octane non-ethanol fuel?
 
Last edited:

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Re-clean your carbs take the welch plugs out did you soak or spray them or just re-place parts. Did you do a link and sync when you put the carbs back on. 87 octane is fine for that motor.
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
The leaf valves tend to last a long, long time. I've never broken one nor had problems, but I have replaced a number of sets on my V6 engines with the new carbon fiber type reeds. A performance improvement-not as a result of a metal reed problem. I run ethanol fuel in my engines with no problem. On my old, high compression head models, I do run 92 octane. 97 in the others.
 

jakedaawg

Rear Admiral
Joined
Jun 26, 2012
Messages
4,275
If the bulb wont get hard you have either a bad bulb, or more likely, a heavy float. A carb with a needle not seating explains most of the issues in the original post. I did not read through the whole thread.
 

Kenkuniff

Cadet
Thread starter
Joined
Jul 12, 2016
Messages
7
Took carbs off and cleaned again and they still look good. Bulb still always seemed soft. So I replaced the fuel connector and the fuel line, even though they looked pretty new. Bulb now gets very hard. Couldn't test on lake best weather was crap. Tested with hose and it seems to idle better but haven't tried anything above idle. Thanks again for all the help. Will post again once I can get it on the lake actually and open it up.
 
Top