Just got this 1987 V4 90hp. Never seen it run when i got it.
Done a compression test and pot 3 was 90 where the rest were around 105-110.
I put some 2 stroke down the barrel which brought pot 3 up to 97 so thought nothing else about it. Something i would get around to after the season ends.
I changed the impeller and started her up.
Once it was running, the starboard pots 1 & 3 were crazy hot. You could not touch them.
The tell tale was working pissing as it should ports side was OK but starboard was so hot i could not touch it.
So i took the cylinder head water jacket off to find that it was completely dry.
Next the head came off. I seen a lot of damage to the head. Looks like it caught a ring or this was caused by overheating or detonation or a lean condition.
What do you guys diagnose ?
So the dilemma i am in is i want to run this motor asap.
Can i flush the water system out to clear any blockage.
I read there was service bulletin about moving the tell tale to the top off cylinder 1 to bleed of any trapped air but the tell tale is routed above pot 1 and down the side to try and stop this.
I am at a loss could this just be a blown head gasket ? If it is why are the water passages dry ??
Done a compression test and pot 3 was 90 where the rest were around 105-110.
I put some 2 stroke down the barrel which brought pot 3 up to 97 so thought nothing else about it. Something i would get around to after the season ends.
I changed the impeller and started her up.
Once it was running, the starboard pots 1 & 3 were crazy hot. You could not touch them.
The tell tale was working pissing as it should ports side was OK but starboard was so hot i could not touch it.
So i took the cylinder head water jacket off to find that it was completely dry.
Next the head came off. I seen a lot of damage to the head. Looks like it caught a ring or this was caused by overheating or detonation or a lean condition.
What do you guys diagnose ?
So the dilemma i am in is i want to run this motor asap.
Can i flush the water system out to clear any blockage.
I read there was service bulletin about moving the tell tale to the top off cylinder 1 to bleed of any trapped air but the tell tale is routed above pot 1 and down the side to try and stop this.
I am at a loss could this just be a blown head gasket ? If it is why are the water passages dry ??
Attachments
-
20240311_141133.jpg2.5 MB · Views: 6
-
20240311_141155.jpg4.1 MB · Views: 6
-
20240311_141206.jpg1 MB · Views: 6
-
20240311_141222.jpg3.2 MB · Views: 5
-
20240311_141235.jpg3.6 MB · Views: 5
-
20240311_141245.jpg1.9 MB · Views: 5
-
20240311_141251.jpg1.4 MB · Views: 5
-
20240311_141321.jpg1.7 MB · Views: 6
-
20240311_141325.jpg1.6 MB · Views: 6
-
20240311_141330.jpg1.6 MB · Views: 6
-
20240311_142908.jpg1.8 MB · Views: 6
-
20240311_142913.jpg1.6 MB · Views: 6
-
20240311_142919.jpg1.5 MB · Views: 6
-
20240311_142924.jpg1.7 MB · Views: 6
-
20240311_142927.jpg1.7 MB · Views: 5
-
20240311_142934.jpg1.5 MB · Views: 5
-
20240311_142941.jpg1.5 MB · Views: 5
-
20240311_142952.jpg1.8 MB · Views: 6