1986 johnson 110hp still won't start

Joined
Nov 3, 2013
Messages
15
Re: 1986 johnson 110hp still won't start

I did notice that there is some fuel spraying out of the top of the solenoid where the red knob meets the body of the solenoid. QUOTE]

I'm not familiar with this, maybe someone can chime in re that fuel spraying.

Something not noted (or I missed it), have the carbs ever been cleaned or at least gone thru?

Besides the age of the engine, with the crappy ethonol fuel, if it was stored without draining the bowls, the main and idle jets are likely clogged (they have really, really small orifices). Either Non ethonol fuel or a good fuel stabilizer is ABSOLUTLY necessary nowadays as regular fuel can go bad in as quickly as a month..

You mentioned your engine sputtered a little bit when choked, which makes sense. The engine is getting some fuel (not utilizing the jets) but not enough to run on the jets after that. Simply checking the plugs after cranking over to see if their WET with fuel will let you know IF the engine is GETTING FUEL. The one plug, nice and clean also suggests the cylinder isn't firing, very likely because it isn't getting fuel to burn (and thus leave deposites on the spark plug)

IMHO, the fuel system is by far the weakest link, especially here. To check/clean the carbs is petty simple. Once the carbs are off, simply remove the bowl(s). Access to the jets should be right there. Yellow varnish on the inside of the bowl is a sure tip off as well that the jets are clogged..

Don't just look at the jets, pull them and make sure you can see light all the way thru the jet. As small as some of the jets are, should you need to poke a piece of wire to dislodge any crap (carb cleaner, air compressor doesn't work), a cut off piece of wire from a WIRE BRUSH, clamped in a small vise grip should fit thru.
 

Bee Reel

Cadet
Thread starter
Joined
Jul 28, 2013
Messages
29
Re: 1986 johnson 110hp still won't start

I had the flywheel nut off because I was going to pull the flywheel to switch out the stator which was testing below what cdi recommends it test at. I decided to talk up my issues with all of you before I did it so I put the nut back on and tightened it with my torque wrench. An you guys are right, I guess I never saw it run well. Just in a bucket and only for a short time. Started for me every time I started it (3 times) while still on my homemade motor stand and some muffs. Im sure that many parts have been swapped....the guy who sold it to me gave me a create filled with coils, stators, vro pumps, another lower end, rectifiers, 2 complete carbs and the list goes on. Also got a 5 gallon bucket filled with every fastener that is on that motor times 500. He was a commercial fisherman and must have worked on his own motors to keep his business alive. Also I have gone through every electrical connection and cleaned them to bare metal. Also replaced the battery leads when I rewired the boat. All are marine grade wire with marine grade connectors and adhesive shrink tubing. I also cleaned the carbs by soaking them in carb cleaner and blew every port, hole, ect out with compressed air.right mini light to make sure I could see through the jets/ports. I used rebuild kit and did them all over. Floats, needles, o rings, gaskets, and freeze plugs. Got them clean enough to eat off of. Haha.
 

daselbee

Commander
Joined
Jan 20, 2009
Messages
2,765
Re: 1986 johnson 110hp still won't start

Well, I guess I don't understand what it is doing....You should be able to spray pre-mix in the carb throats, and with good compression and good spark timed properly, the engine will fire up and at least run until that gas you sprayed in is gone. Are you saying you cannot get it to do even that? I gotta stand by what I posted earlier....if you spray pre-mix in the carb throats, and it does not fire up and run for a few secs, then I suspect the timing is off due to a sheared flywheel key, or mis-wiring of the coil primaries. It is possible, but not likely that the timerbase is wired wrong to the pack...but that is a long shot.
 

Bee Reel

Cadet
Thread starter
Joined
Jul 28, 2013
Messages
29
Re: 1986 johnson 110hp still won't start

Daselbee, I had sprayed the fuel into the throats of the carb alone and tried to turn it over after doing so. Maybe not the best way to do it....Im gonna try to spray the fuel mix into the carb throats while my friend turns her over....I just picked up a 1972 Evinrude Lark yesterday model number 50273c for $50. I couldn't pass it up since it seemed to be all there and the compression seems good. My father works at a scrap yard in RI and one came in with some other random items. Gonna try to get that one going as well just in case the 110 Johnson is done for or as a motor to sell off to try and recoup some money I've put into my current rig. Big difference in hp I know, but my 1980 Chrysler tri hull is only rated for 75 hp anyway and I've been told that the 50hp will move the Bee Reel just fine. I have no current aspirations to pull tubes or skiers...just fish some local lakes and a great place called Narrow River for some striper. As a last ditch effort I'm gonna have a local marine mechanic take a poke at the Johnson. Id really like to get it going. Partially just not to feel like it beat me and partially because deep down I hope the gentleman that sold it to me didn't take advantage. There are lots of dishonest people in this world but I still have hope for all of them. Ha! On the bright side I consider all of you that are trying to help this hardworking dad out as friends and money cant buy those. If any of you find yourselves headed towards my little ol' state of RI drop me a line, Ill be happy to show you where all the fish are. :)
 
Top