1978 Evinrude 4hp 2 stroke Model 4806E (Hard starts)

rudemotor

Cadet
Thread starter
Joined
Apr 26, 2018
Messages
7
Hello everyone, I'm 60yrs old no nothing about motors. Thought I could buy a small engine to go on my Jon boat and do some fishing.(Headache)
Here's my story:
I just bought this motor and it ran at the persons house. The man that I bought it from redid the carburetor and put in a new impeller.He said its a great running motor and you will have no problems. I said that's what I want. I loaded it my truck by laying it on its side. When I got home I put it on the engine stand he gave me. A few days past due to being cold and the ice was still on the lakes here in New Hampshire. We had a nice day so I put the boat in the water with the motor.. I tilted the motor up so it wouldn't hit the bottom of lake shore. I got out where it was now deep and the motor started right up. I got about 150 yards and the motor stopped running. I kept trying to pull the rope cord to start but nothing. Luckily I brought my trolling motor along and got back to shore. I called the guy back and told him what happened and he said sorry it ran when I sold it to you and it was as is, which he didn't say at the sale. So I hung up because I knew he wouldn't help me.

The next day I put the motor in a garbage can to see if I can start it. I get the motor started after a few pulls and let it run for a while.I then shut it down and can't get it started again. If it sits for a long time I can then restart it after many pulls. I tested for spark and I do have that. I have water coming out the peep holes. The compression test out of each cylinder was 30. He said the compression was good when I bought it, I didn't do a test at his house because the engine ran fine. Model

Could I have caused the problem when I tilted the motor up and forgot to put it back down to the bottom position. The bottom of motor was in the water and moving me along?
The starter, pulling the rope seems to pull sluggishly, could that be due to the cold? Then it pulls fine afterwards.
Could laying the motor on its side cause problems.
He gave me the gas can with gas in it.. That was what we used when running motor which ran fine. I dumped that out and got fresh gas 91 octane to see if that might help (it didn't).

I never dealt with engines, I wanted something that I could put in the water and go fishing..e tune ups and self maintanance, Hopefully I wasn't ripped off and it doesn't turn into something major. PLEASE HELP!!!!!
 

rudemotor

Cadet
Thread starter
Joined
Apr 26, 2018
Messages
7
Gas and oil mixed at 50:1 ?

Yes the mixture is 50:1. As I said in my short story, sorry for all the details, but I wanted to be clear on what happened.
Could I have caused the problem when I tilted the motor up and forgot to put it back down to the bottom position. The bottom of the prop was in the water and was pushing the boat along.
 

rudemotor

Cadet
Thread starter
Joined
Apr 26, 2018
Messages
7
As I said I am new to this. I was reading my manual and it said to disconnect the 4 wire before doing compression test. Why is that?
 

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
As I said I am new to this. I was reading my manual and it said to disconnect the 4 wire before doing compression test. Why is that?

Dunno which 4 wire(s) you refer to but it is probably to render the ignition system inoperative during the compression test. You can do the same by grounding the plug wires.

You may have starved the engine of cooling water, by running with it tilted, and caused severe damage to the pistons, rings or cylinder bores due to over heating. Discolored paintwork maybe a clue if you have but a compression test should confirm one way or the other.
Do at least 6 pulls of the rope on each cylinder and record the maximum readings you get.

Report the results here for evaluation.
 

rudemotor

Cadet
Thread starter
Joined
Apr 26, 2018
Messages
7
What 4 wires. Explain ??

The 4 wires is a plug. Seeing that this is electronic ignition the manual says to unplug that before doing compression test. It is what Vic S said it renders the ignition system.
 

rudemotor

Cadet
Thread starter
Joined
Apr 26, 2018
Messages
7
Dunno which 4 wire(s) you refer to but it is probably to render the ignition system inoperative during the compression test. You can do the same by grounding the plug wires.

You may have starved the engine of cooling water, by running with it tilted, and caused severe damage to the pistons, rings or cylinder bores due to over heating. Discolored paintwork maybe a clue if you have but a compression test should confirm one way or the other.
Do at least 6 pulls of the rope on each cylinder and record the maximum readings you get.

Report the results here for evaluation.

Hey Vic, I did the compression test as you said and I am getting 30. I did 6 pulls on each cyl and both are reading 30. I even took the motor to a car repair shop and they came out with their tester and got the same reading. Is it a big project to check damage to the pistons, rings, or cylinder bores? How much does something like this cost to repair. Again thanks for replying with your knowledge.
 

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
It is a pretty small simple outboard so tearing down is also a relatively small simple job but If you know nothing about engines then there is fair bit to learn

Until it is dismantled you wont know how much damage has been done but with compression figures as low as 30 it might be severe.
I guess you could replace both piston and ring assemblies for about $160 but if the cylinder bores are damaged its probably beyond economic repair.

A harsh lesson learnt I am afraid
 

guyboyajian

Cadet
Joined
Apr 14, 2018
Messages
19
It is a pretty small simple outboard so tearing down is also a relatively small simple job but If you know nothing about engines then there is fair bit to learn

Until it is dismantled you wont know how much damage has been done but with compression figures as low as 30 it might be severe.
I guess you could replace both piston and ring assemblies for about $160 but if the cylinder bores are damaged its probably beyond economic repair.

A harsh lesson learnt I am afraid

I'm going to take the cylinder head off and see what it looks like. If it doesn't look bad I will put a new head gasket on and hopefully it gives a good compression and starts. Thanks
 

guyboyajian

Cadet
Joined
Apr 14, 2018
Messages
19
Pull the cylinder head and see what you find.

I'm going to take the cylinder head off and see what it looks like. If it doesn't look bad I will put a new head gasket on and hopefully it gives a good compression and starts. Thanks
 

Vic.S

Rear Admiral
Joined
May 4, 2004
Messages
4,721
I'm going to take the cylinder head off and see what it looks like. If it doesn't look bad I will put a new head gasket on and hopefully it gives a good compression and starts. Thanks

If you also take the exhaust cover plate off you will be able to get a glimpse of the pistons and rings,
 

rudemotor

Cadet
Thread starter
Joined
Apr 26, 2018
Messages
7
Hi everyone, this is the scoop on my motor. I found a guy in town that does vintage motors. He told me it’s not worth putting any more money into the motor. The guy that sold it to me was not as nice as I thought. He took the $325 and then wanted nothing to do with me. I wouldn't have minded if weeks or months went by and I ask him to help me but it was only a couple of days when I put it in the water and only went 200 yards and it shut down. I would call him for some assistance and he would recommend things to do, even though he knew I knew nothing. I told him what I learned in this Forum and he said they don't know what it is. So I said the motor will become a door stop. This motor repair guy was like an angel. He took the messed up motor and gave me one of his. It's nice that some people don't think of the all mighty dollar. He understood that this was my first gas motor and new nothing about them. I spent 2 hours at his place and he showed me about the engines and how they run and what does what. He wanted to see me out on the water with my grandchildren and wife fishing. I know that there are people out there just like you guys trying to help people. THANKS TO EVERYONE. God Bless
 

guyboyajian

Cadet
Joined
Apr 14, 2018
Messages
19
Hi everyone, this is the scoop on my motor. I found a guy in town that does vintage motors. He told me it’s not worth putting any more money into the motor. The guy that sold it to me was not as nice as I thought. He took the $325 and then wanted nothing to do with me. I wouldn't have minded if weeks or months went by and I ask him to help me but it was only a couple of days when I put it in the water and only went 200 yards and it shut down. I would call him for some assistance and he would recommend things to do, even though he knew I knew nothing. I told him what I learned in this Forum and he said they don't know what it is. So I said the motor will become a door stop. This motor repair guy was like an angel. He took the messed up motor and gave me one of his. It's nice that some people don't think of the all mighty dollar. He understood that this was my first gas motor and new nothing about them. I spent 2 hours at his place and he showed me about the engines and how they run and what does what. He wanted to see me out on the water with my grandchildren and wife fishing. I know that there are people out there just like you guys trying to help people. THANKS TO EVERYONE. God Bless
 
Top