1976 Sea Ray SRV195 project

Paul2375

Cadet
Thread starter
Joined
May 8, 2016
Messages
24
Hey all,
So stumbled upon a 1976 Sea Ray with trailer and 140 Johnson outboard for a great price. Picked it up back in September and have worked on it getting ready for this summer. My friend helped out getting the motor working right and took it out for a test ride last week. All was fine until he turned the wheel one way and the boat went the other way. Got it out of the water and transom is rotted and exterior fiberglass is cracked. We had tested the integrity of the transom back in September and thought we were good. So now, after all the refurbishing, back to square 2 I guess. Attached are some pics of the damage...I am planning on attacking this from the exterior. Any input and ideas would be very appreciated!!
 

jbcurt00

Moderator
Staff member
Joined
Oct 25, 2011
Messages
25,352
I suspect you'll have more to replace then 'just' the transom....

Dig in to other topics here in the resto forum.

Good luck w your project and welcome to the dry dock at iboats.

From the exterior wouldnt be a method I'd suggest for transom replacement, even w the huge crack you've got.

Just for reference and to help others in the future, how did you assess the transom back in Sept and decide it was good? That type of failure didnt occur because of a problem that started after you bought it. It was a long time coming.
 

Paul2375

Cadet
Thread starter
Joined
May 8, 2016
Messages
24
I did check the transom back when I bought it ($100), but it seemed stout then. Not sure at this point to either junk the boat, keep the motor and trailer and find a new shell.
 

jbcurt00

Moderator
Staff member
Joined
Oct 25, 2011
Messages
25,352
I was asking HOW you checked the transom. Not a critique, just that whatever the method, it wasnt an accurate assessment.

Unless you LOVE that hull, a little bit of an education, a decent (running?) motor and a decent trailer (towable?) for a 100, sounds like a fairly good deal.

Lots of other project hulls that dont have the transom half peeled off.
 

Paul2375

Cadet
Thread starter
Joined
May 8, 2016
Messages
24
I just jerked on the motor about 6 or 8 times and did not feel any play...granted probably not the most accurate test.

Playing this card, the trailer is fine and motor is good, what would be the most likely candidate for a replacement hull?? Another fish/ski?
 

Vintage Rider

Seaman
Joined
Mar 6, 2016
Messages
62
I'd say you got a terrific deal regardless of what you decide to do with the hull. If you decide to fix this one, plan on replacing stringers and floor as well as the transom. If you find another boat of the same vintage or even one twenty-five years newer, plan on the transom, stringers and floor needing replacment, unless you're really into exciting boat rides. If that's the case, wear a life jacket and stay close to the shore.
 

Paul2375

Cadet
Thread starter
Joined
May 8, 2016
Messages
24
Yeah it was definitely a deal
I'm gonna ride the repair route and see where it goes
Many pics will be coming soon
 

Paul2375

Cadet
Thread starter
Joined
May 8, 2016
Messages
24
Interior work completed.
 

Attachments

  • IMG_1855.JPG
    IMG_1855.JPG
    178.6 KB · Views: 0
  • IMG_1832.JPG
    IMG_1832.JPG
    109.9 KB · Views: 0
  • IMG_1851.JPG
    IMG_1851.JPG
    89.2 KB · Views: 0

jbcurt00

Moderator
Staff member
Joined
Oct 25, 2011
Messages
25,352
I dont know how you removed and replaced the deck plus the entire interior basically overnight, but it isnt 'repaired' and probably isn't completely safe.
 
Last edited:

Paul2375

Cadet
Thread starter
Joined
May 8, 2016
Messages
24
Well, all the decking and interior was done earlier this year, not last night. Was having the boat tested after getting the motor finally running correctly and then the transom cracked.
 

Woodonglass

Honorary Supreme Mariner
Joined
Dec 29, 2009
Messages
25,933
Just out of curiosity did you seal the plywood deck with anything prior to carpeting??
 
Top