HaplessBoater
Recruit
Thread starter- Joined
- Sep 24, 2017
- Messages
- 4
Hello Forum Members! This is my first post and I hoping to tap into your collective wisdom to get this old 25 running like a top!!
Here is the story so far ...
Purchased in semi-running condition. Would start and run on one cyl in a tank. Fuel tank was ? full of water and one of the hose ends was broken (this was not the tank that the motor was test run on). Compression was 95 psi in top cyl and 100 psi in bottom cyl at purchase. Since then compression check shows top cyl at 100 psi and bottom cyl at 118 psi. I am concerned that the top cyl is damaged (scored cyl, piston, broken ring).
Symptoms
Very hard to start, and if it does start will run on 1 cyl and then quit. If you are quick and get it in gear and advance the throttle to wide open it will run ok. Even at high speed there is an occasion momentary ?hiccup?, but it will keep going. Upon return to shore as soon as the throttle is reduced to ? or less it cuts to 1 cyl and then quits. Very hard to restart.
Done So Far
Thanks for your help!
Here is the story so far ...
Purchased in semi-running condition. Would start and run on one cyl in a tank. Fuel tank was ? full of water and one of the hose ends was broken (this was not the tank that the motor was test run on). Compression was 95 psi in top cyl and 100 psi in bottom cyl at purchase. Since then compression check shows top cyl at 100 psi and bottom cyl at 118 psi. I am concerned that the top cyl is damaged (scored cyl, piston, broken ring).
Symptoms
Very hard to start, and if it does start will run on 1 cyl and then quit. If you are quick and get it in gear and advance the throttle to wide open it will run ok. Even at high speed there is an occasion momentary ?hiccup?, but it will keep going. Upon return to shore as soon as the throttle is reduced to ? or less it cuts to 1 cyl and then quits. Very hard to restart.
Done So Far
- Discarded old fuel, cleaned and dried inside of tank (no corrosion
), drained fuel line, replaced hose end. Noticed that the fitting on the fuel tank does not seal correctly when the fuel line is disconnected. Fuel continues to flow out of the tank with the fuel line disconnected, so the o ring in the fitting at the tank needs to be replaced. Have not done this yet but will.
- Fresh premium fuel mixed 50:1, with stabilizer and SeaFoam
- Removed electric starter motor, electric choke, electric start lockout switch, and what remained of the neutral crank lockout mechanism. Installed new lanyard style kill switch (when closed the switch connects the 2 coils - I have confirmed the correct operation of this switch) and a bolt to block off the threaded hole in the top cyl. (that holds the crank lockout mechanism).
- Replaced fuel line from fuel pump to carb
- Replaced hose from upper bypass cover to bottom of intake manifold (fuel recirculation hose)
- Cleaned filter screen at fuel pump. Didn?t see anything on it.
- New spark plugs (Champion J6C). Gapped at 0.030?
- New coils, points (set to 0.020?), condensers, driver coil
- New impeller, wear plate. There is some water in the gear case oil, and I have a seal kit to replace the seals and o rings. Just didn?t get to it yet.
- Carb remove, complete disassemble, cleaned with carb cleaner and passages blown with comp air, and rebuild kit (float, float valve, gaskets). Set float as per specs (level when inverted, and correct drop down).
- Removed intake manifold and reed valves to inspect. Looked ok. Some minor corrosion on lower left side of the manifold and reed valve plate where the fuel recirculation hose enters. But condition of reeds overall seems fine (no cracks, chips, sealing well, etc.).
- Have not pulled head or bypass cover to look at condition of top cyl and piston.
- Have not checked to see if the thermostat is in place. In high speed running there was no evidence of overheat.
Thanks for your help!