1971 Johnson 9.5 - On a mission to sort out low idle problems

knate

Cadet
Thread starter
Joined
Jul 22, 2015
Messages
6
Hi all,

As the title states, 1971 Johson 9.5hp. Low hours on this motor and very clean, I picked it up last year from a guy who said ever since he's owned it it's had a rough idle. He always just dealt with it. The spring of last year the carb was rebuilt.

My symptoms:
-Motor starts right up with easy pulls but must be opened up slightly to keep running. To shift into gear it must be quickly down throttled switched into gear, and then throttled up. I don't want to keep doing this because I know this is not good for the gears/clutch dog.

-Runs beautifully when given gas above idle, no sputtering, wide open throttle has great power (Got our 11 foot john boat up to 15mph)

-I have played with slow speed adjustment to no end. The knob also does not seem to impact the engine rpm whatsoever whether all the way in or backed way out. I'm thinking this may partly be where my problem is. If throttle is slightly open does this knob become irrelevant?

-Engine cover on/off also has no effect on idling performance.

-I replaced the upper crankshaft seal last year, problem did not change (No leaking fluid on seal but since flywheel was off I changed it anyway)

My thoughts are that, either I have an air leak somewhere or clog. I have a carb rebuild kit on the way and will start there. Going to pop some new spark plugs in as well because I don't know the last time they were changed. Does anyone have any other suggestions or experience they'd like to share? Is it possible my slow speed jet is clogged?

I'm a bit of an amateur so please excuse my ignorance. I plan on updating this thread until it is solved. I love this motor and really want it to be tip top.

Thanks,
Nate
 
Last edited:

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
How's the tip of the needle valve? If it's bent or distorted in any way, it won't have the effect it's supposed to have. Your mention that turning the needle valve has no effect points at something along those lines. Also, could be some crud in that circuit inside the carb.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Maybe the throttle plate opens up too early.---------The motor should sneeze if low speed mixture needle is screwed in too far.----And which idle adjustment knob did you play with ?
 

knate

Cadet
Thread starter
Joined
Jul 22, 2015
Messages
6
Thanks Chine, I want to say I took it out and it looked good last year. But I will pull it tonight and post a picture to get a second opinion. That is my suspicion as well right now.
 

knate

Cadet
Thread starter
Joined
Jul 22, 2015
Messages
6
Hi Racer, I played with the one on the front of the motor (the low speed needle), not the one on the tiller handle. I know the throttle plate opens on the right timing because I adjusted the armiture last year, it was a little off to begin with. As soon as the throttle is opened slightly it runs well, it's when the throttle plate is fully closed that I have the problem.

If that low speed mixture needle is all the way in and the throttle is slightly opened would the motor theoretically still sneeze?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Motor will not run / idle when low speed mixture is all the way in.
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
The one on the base of the tiller handle is only a stop for the throttle. Helps if you troll a lot, allows modest hands-free operation as the throttle won't walk to a stop position. Basically sets the low point of the throttle adjustment.
 

tomhath

Master Chief Petty Officer
Joined
Dec 5, 2007
Messages
814
The low speed circuit is simple. The needle lets fuel into a small chamber that's under the welch (freeze) plug. From there it flows through a few very small holes into the back of the carb throat behind the throttle plate.

So you need to be sure:

1) packing around the needle isn't leaking air
2) screwing the needle all the way in closes off the inlet
3) the small holes that let the fuel out are clear

You'll need to remove the welch plug for #2 and 3. It's easy to remove and replace, search for videos online if you've never done it. You can't diagnose the idle problem without pulling that plug and repacking the needle.
 

ultra353

Petty Officer 1st Class
Joined
Jun 21, 2009
Messages
388
Possible lower crankcase seal leak or crankcase halves leaking. No matter how you adjust the carb it will have a lean miss. I have a '71 9.5 that is leaking at the halves and won't idle without the miss . Above idle, runs good.
 

HighTrim

Supreme Mariner
Joined
Jun 21, 2007
Messages
10,486
As I remember back tuning various 9.5s, I have found this same scenario, with many different issues.

I had one that gave me a heck of a time to diagnose. Ended up the actual carb casting was leaking air in.

As stated, the crank halves, or crank seals leaking.

More times than not though, the throttle plate is not adjusted properly. They are actually pretty sensitive. They open a bit too early, and you will get that lean sneeze at idle. If you don't have the procedures for setting it properly, let us know.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
So, trying to understand the problem--is it sneezing or not? Too lean will make it sneeze, as will incorrect throttle plate adjustment or air leaks. Too rich without sneezing is a different story. How about the front motor mount? Is it broken? If so, the powerhead will flop around in there and won't idle well. A common problem.
 

knate

Cadet
Thread starter
Joined
Jul 22, 2015
Messages
6
Hey everyone, thanks for the suggestions. Second winter (complete with rain and snow) has hit Wisconsin this weekend so I haven't been able to get to much yet. I promise to update on my progress as it goes along.

F_R - The engine will die out if the throttle plate is not engaged a little bit, I have to start the engine with the throttle slightly open. However, it starts on first couple of pulls and once its been started, will start first pull. Motor mount is intact, I've read this style of motor was prone to vibration, but it really doesn't vibrate all that bad when running.

Love to learn so question for you: if the throttle plate adjustment is incorrect, won't the timing be off when the throttle is revved also? From the lowest idle I can get (throttle slightly engaged), to wide open the engine is very smooth.

I will try to pull the slow speed needle Sunday morning and get a picture up.

P.s. I apologize the post title is misleading, I meant to say won't idle and I guess the fingers went with "low". Sorry about that.
 
Last edited:

HighTrim

Supreme Mariner
Joined
Jun 21, 2007
Messages
10,486
Make sure you hold the throttle shaft FULLY CLOSED when doing this.
 

Attachments

  • Omc 9.5hp Linc n Sync.PNG
    Omc 9.5hp Linc n Sync.PNG
    289.8 KB · Views: 15
  • Omc 9.5hp Linc n Sync Pic.PNG
    Omc 9.5hp Linc n Sync Pic.PNG
    588.7 KB · Views: 16

tomhath

Master Chief Petty Officer
Joined
Dec 5, 2007
Messages
814
Love to learn so question for you: if the throttle plate adjustment is incorrect, won't the timing be off when the throttle is revved also? From the lowest idle I can get (throttle slightly engaged), to wide open the engine is very smooth.

The motor will run fine if the spark advance is off by a few degrees. At high RPMs you lose some power.
 
Last edited:
Top