1966 9.5 sportwin spark issue

Mbo1979

Cadet
Thread starter
Joined
Dec 29, 2015
Messages
8
I replaced the whole ignition system coils condensers points set points replaced ignition wires spark plugs and cleaned everything thoroughly set the points not sure what else to do I also disconnected the kill switch it's driving me nuts any ideas what it can be?
 
Last edited:

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Not a lot to go by , but is the cam upside down ?------Those mags are elegantly simple and with all that work and parts you should have spark that jumps a gap of 1/4" or more.
 

HighTrim

Supreme Mariner
Joined
Jun 21, 2007
Messages
10,486
Even new points often need cleaning and/or dressing. Especially nos ones.

Are the coils heels flush with the mounting boss? Should not be able to catch your nail running up the boss, but should not be too far back as to limit spark.

Did you test continuity through the coil to the spark plug boot? Ensure good connections along the way like at coil. You should get about 3000 to 8000 ohms resistance (this is secondary winding) from the spark plug boot, to the coil ground lead.

Run some wet/dry, or a points file, through the points many times. Blow off with compressed air. Dip paper stock, or a business card in acetone and run that through to clean. Then blow off with compressed air again. The littlest bit of dirt can limit spark.

I assume you have the points set to 020 when the widest part of the cam is aligned with the rubbing block of that points?

The spark plug spring punctured on center through the new plug wire? Cut back 1/4" of insulation on the wire there, fold the ends back, then insert the spring. Spray with wd40 then insert into the boot.

On the other end of the spark plug lead, the lead need to be pulled through the mag plate, TWISTED into the coil, so the strands wrap around the pin, then pull excess wire back through the plate, and tighten down coil. Don't forget to re attach clips that hold leads to bottom of plate, clean and re grease bottom of plate, before re installing. Not too much grease either, or it will get thrown off and foul the points.

After all said and done, the spark should easily jump a 1/4" gap on an inline tester with a bright blue ZAP!!
 

steelespike

Supreme Mariner
Joined
Apr 26, 2002
Messages
19,069
Did you torque the flywheel? Bore and crank shaft key way clean and dry? nut to 480 - 540 in. lb.Is the flywheel key and keyway in good condition?
 

Mbo1979

Cadet
Thread starter
Joined
Dec 29, 2015
Messages
8
Didn't torque the fly down completely and yes the key appears to be in good shape
 

Tim Frank

Vice Admiral
Joined
Jul 29, 2008
Messages
5,354
What were the symptoms that had you change out all those components?
 

Mbo1979

Cadet
Thread starter
Joined
Dec 29, 2015
Messages
8
Before I changed it I only had one spark plugs sparking engine has been sitting for about five years so I thought it was a good idea to change the whole ignition system don't really understand why I can't get any spark
 
Last edited:

Tim Frank

Vice Admiral
Joined
Jul 29, 2008
Messages
5,354
Most common problem I've seen after a full R&R when there is zero spark is the HT connections at the coil.
Per High Trim's [post (#3) :
On the other end of the spark plug lead, the lead need to be pulled through the mag plate, TWISTED into the coil, so the strands wrap around the pin, then pull excess wire back through the plate, and tighten down coil.

At the bottom of the coil bore where the HT leads go, is a spiral connecting post that acts like a thread.....you need to "twist" the wire onto them to get a proper connection.
It is a good habit to measure the full depth of that bore and mark that depth on the wire with a piece of masking tape so that you are sure that you have full engagement.
 

AlTn

Commander
Joined
Mar 9, 2010
Messages
2,813
make certain your spark checker is on a good grounding point
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
^^^^That's a good point. (Can't tell how you are testing -- might be laying the plug on the block, then spinning the flywheel by hand.) HighTrim posted a nice list of tests and checks -- would start with a proper spark tester with good ground.
 
Top