1956 Evinrude 30hp Big Twin, help identify unknown piece

Maddison III

Cadet
Thread starter
Joined
Mar 9, 2016
Messages
6
Bought a wooden 1955 Bowman Rascal w/ original 1956 Evinrude 30hp Big Twin and original trailer. I have the service manual, and other guides from the net. I cannot yet post pictures, so please bare with me. So far, I have completed the following on the motor: Rebuilt carb, new coils/points/condensors/plugs/wires, new fuel/air lines, new water impeller, and new lower unit seals. I have two questions:
I cannot identify the vaccum?/fuel? port directly (approx 1 inch) aft of the carb filter bowl. I reassembled everything as it was the way I aquired it (which may not be right), and as far I can tell, correctly based on various schematics. Fuel and air is hooked up with new lines, this third mystery port did not have anything attached, and I can not find it in any schematics. What is it?

When replacing the water impeller (has been replaced before), a woodruff key fell out. The drive shaft has a pin on it and no indentation for a woodruff key. I've seen schematics with a key, and another one with just the pin (no woodruff key). I did not see where it was installed, and it will not fit in the impeller because the shaft does not have a slot for it. Does the impeller supposed to have a woodruff key, and if so where does it go?

Thanks in advance
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
couple of guesses. It sounds like there could have been an attempt to install a fuel pump, with pulse source from a bypass cover. Any other evidence of a fuel pump -- maybe know something about the history?

On the impeller, I would get a pin for the shaft (can't quite see how a key would work if no slot for it). Some motors used the key that was a combination key and pin (for lack of a better description) -- not sure about the '56 Big Twin. Thinking that combo key was used in smaller outboards.

Kind of sounds to me like a PO did some tinkering. Guess I would check for evidence of overheating (pump not functioning), and take a compression test. Would want to do the latter anyway, and maybe have done that.
 

Maddison III

Cadet
Thread starter
Joined
Mar 9, 2016
Messages
6
I read posts on the fuel pump conversion. Boat/motor came with two pressure tanks and fittings. Engine shows no other signs of fuel pump mods. It's been sitting in a barn for 20 years, but other than that it's in great shape. The mystery port appears to be built in. It's a bit rusty, like nothing has been attached for quite some time. The shaft has the pin, and spins the impeller just fine. A bit worried where that key came from and if I will be OK with out it. A few more posts and I can post pictures, it sure would be helpful. Compression is good, no signs of overheating. Definitely tinkered with though: fly wheel nut loose, lower unit not sealed and leaking, one additional wire from a coil I assume was from a cut off switch. The joys of a PO
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Keep posting (I mean, nice hearing from you, but want to see those pics....). I think I know that little hull . Will do some google searches. Think the trailer might have teardrop fenders and painted hubs (with baby moons)!

good find.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
able to see the pic. Not what I thought (not bypass cover) -- possible though that it was a failed attempt to pick up a pulse from the intake manifold.

(Edit. at least think that would be a failed attempt -- wouldn't expect it to work.)
 
Last edited:

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Simple. That vacuum nipple is for the hose that leads to the vacuum cut-out switch. And that extra wire in the magneto also leads to the vacuum cut-out switch. Obviously, the switch wasn't installed when you snapped the picture, because it is mounted to the bracket that holds the recoil starter, etc.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
No Title

Vacuum cut-out switch consists of all the parts in upper right hand corner of this picture. Attached to bracket #41
 

Attachments

  • photo239353.jpg
    photo239353.jpg
    176.8 KB · Views: 3
Last edited:

bwkre

Petty Officer 2nd Class
Joined
Jul 11, 2010
Messages
187
Just a guess but you indicated that you did the lower unit seals. Could the key be from the gear on the end of the drive shaft? You would have removed the shaft for seal replacement
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
NOPE-----There are no keys used inside the gearbox on those bigger motors !
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
There are no woodruff keys anywhere on a '56 30hp. Except the flywheel key and it would be a stretch to call it a woodruff key. Besides, it would be nearly impossible for it to wind up around the water pump. Yes. the impeller is driven by a round pin.
 

Maddison III

Cadet
Thread starter
Joined
Mar 9, 2016
Messages
6
Thanks for all the replies! Here's a pic of the boat. Yup, last registered 1989, been sitting in a barn ever since. Everything is intact (except the vacuum switch apparently), just needs a good rub down. So, the motor doesn't have the vacuum switch installed anymore, the wire from the coil was just dangling there, so I removed it. After some research, my understanding is that the vacuum switch was a Rev limiter, and to shut the motor off, I need to lower the throttle and pull the choke. Am I correct? The Rev limiter sounds pretty important, should I get one and hook it up properly? Thanks for the info on the woodruff key (or lack there of). I'm having trouble finding information pertaining only to my motor. You guys have been very helpful
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
OK, here is the truth concerning the vacuum cut-out switch: If you rev that motor up beyond fast idle speed in neutral (or break a shear pin at speed) it will run crazy wild. That is, it will keep on revving out of control even with the throttle closed. And you may not be able to stop it. Pulling the choke knob only makes it worse. Enter the vacuum switch. It senses a runaway condition by monitoring the intake manifold pressure (vacuum). If in runaway condition, the vacuum will be abnormally high and the switch senses that. If a runaway condition is occuring, the switch closes, which shorts out the ignition to the lower cylinder. Once the RPM and vacuum returns to normal, the switch opens and the lower cylinder starts firing again, and everything returns to normal. Till next time.

Lots of people think that switch causes all sorts of evils and remove it and throw it away. But it is impossible for the switch to do anything at all unless a runaway condition exists. So it is not the imagined cause all those other ills.
 

Maddison III

Cadet
Thread starter
Joined
Mar 9, 2016
Messages
6
I have a vacuum switch on the way. In the mean time, I'd like to install the wiring for it. The engine had a single wire connected to the coil, clipped and just left dangling. I haven't found a picture or helpful schematic of the correct wire routing. It obviously needs slack for the armature plate to rotate. Any ideas on source for proper routing?
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
The open one in the picture is for the vacuum cut-out switch.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
No Title

Here ya go---this one has a second wire because it has a key switch to turn the motor on & off.
 

Attachments

  • photo239381.JPG
    photo239381.JPG
    365.1 KB · Views: 0
Top