Search results

  1. jhetrick55

    Cooling issue... '89 VP AQ271C

    I have the engine I mentioned in the thread. I'm having cooling issues. Here is what I've done so far: 1. Replace the connection from the drive to the hose which runs through the transom. This includes removing the upper gear housing and replacing the seals on the bottom of the gear housing...
  2. jhetrick55

    1989 Volvo Penta AQ271c cooling system

    Hey, I'm looking for some advice on part of the cooling system on this engine. Where the raw water hose comes through the transom, it goes into a plastic fitting which turns into a black tube with a couple rubber hoses coming off of it and at the top it goes into the raw water hose which runs to...
  3. jhetrick55

    Newbie to i/o - 1989 Volvo Penta aq271c

    Hey there, I am gonna do my first oil change on the aforementioned vp engine. If reading correctly, vp is recommending 10w-40 synthetic in their engines, even the older ones like mine. Anyone have a recommendation for oil and filter? Currently there is a Wix filter on it, but I do have the...
  4. jhetrick55

    AQ271c overheating

    Hey, I was given a 1989 Carver Montego 23 with an '89 V-P AQ271c. Currently the boat will run and sounds healthy, but it is overheating. I've replaced impeller and circulating pump and I've checked as much of the system as I know how to make sure water is able to move through the engine. Does...
  5. jhetrick55

    '72 100hp Johnson Hydro Electric

    I have the motor from the post's title. I've been noticing if I pull a tuber, or anything else, even at slower speeds, the motor runs rough for a short time and sometimes pops out of gear, but this is rare. I know strong battery connection is essential for these engines, and the battery cables...
  6. jhetrick55

    Engine height... Excessive spray from right and left of the engine.

    I have a 100hp 1972 johnson that I think may be sitting too low on my boat. There seems to be excessive spray both right and left of the engine especially at cruising speeds (20-30mph). I tried attaching some pics, not sure if it's working. The cavitation plate seems to be about an inch below...
  7. jhetrick55

    Bad clutch dog or something else?

    I have a '72 Johnson 100 with the hydro-electric shift. Tonight we were out for a cruise around the lake at about 5mph. About 30 minutes in the boat just died... It ran a little rough before that, but stayed running and kept us moving. After that we couldn't drive it more than 100 yards without...
  8. jhetrick55

    Sludge from exhaust/tailpipe on '72 Johnson 100hp

    Hey everyone, yesterday I got my boat running for the first time this year. This morning I came outside and looked at it and I noticed a decent sized spot where it appears oil and/or other sludge drained out of the tailpipe overnight. Anyone have any ideas if this is normal? Last winter is was...
  9. jhetrick55

    1972 Johnson 100hp pulling a tuber

    I've got a '72 Johnson 100hp electric shift engine on a '72 Glastron V176. Since I got it, it has always run fine. However, at the end of last year I was trying to pull someone on a tube and every time I gave it throttle with the tuber hooked up it would die. Someone suggested maybe it is the...
  10. jhetrick55

    '72 Johnson 100hp Cuts Out

    Last time I had my '72 Glastron Swinger with '72 100hp Johnson out, trying to pull a tube with a young teenager on it, the engine died every time I tried to accelerate. I cannot figure out why this might be. I do have a suspicion the clutch dog needs to be done, but I don't think that would kill...
  11. jhetrick55

    Original Cover and center windhsield - 1972 Glastron V-176 Swinger

    Hey everyone, I hope this is the right place for this question. I recently bought a '72 Glastron V-176 Swinger in excellent condition and I am looking for an original snap on cover for the back end of the boat. I have seen very few of these online when I look around and just wonder if anyone...
  12. jhetrick55

    1972 Johnson 100hp - Hydro-Electric Lower Unit Oil

    I just became the owner, well a week ago, of a 1972 Johnson 100hp engine that is in phenomenal shape. However, with the Hydro-Electric shift I have heard that there is potentially a different lower unit gear oil I will want to use with this engine. Can anyone give me some good suggestions for...
  13. jhetrick55

    Info on 1972 Glastron V-176 'Swinger'

    I just purchased this boat last night with all original paperwork, manual, etc. It is in great shape after only two owners and only being stored inside. I am looking for some help though on the the cover and the center windshield glass. It appears there glass was shattered at some point and I am...
  14. jhetrick55

    NO WOT - 1975 70hp Evinrude

    I have a 1975 70hp Evinrude that was new to me just under two years ago. I have replaced head gasket, exhaust gasket, changed lower unit oil, cleaned/rebuilt carbs and done the impeller. Recently I had it out and it was running fine - 5400rpms and with four people in my boat, about 25mph. All...
  15. jhetrick55

    1975 70hp Evinrude - doesn't get up to speed well

    My 1975 Evinrude 70hp ran fine most of the summer - good idle, good pickup, etc... Then, found out I blew the exhaust gasket and was getting water in center cylinder. Replaced the gasket, took it out to run it and no water in any cylinders, engine would idle fine, but not pick up speed very...
  16. jhetrick55

    Choosing a new prop...

    I have a 1975 Evinrude 70hp with a 13-3/4x15 prop and at WOT I run 3200 rpm, according to my digital tach model: SRT-32R (set to 3p1r). This engine should be in the 5500 RPM range at WOT. I've been looking at a 13-1/4x17 prop, but would like to gain some other perspective. The engine is...
  17. jhetrick55

    Prop Selection

    I have a 1988 Sierra 168V (16 ft fiberglass) with a 1975 Evinrude 70hp engine. I have a 3 blade propeller, not sure of pitch (I will try to find out and post it later - it was on the boat when I bought it). I can hit about 25mph the way it sits. Since the is my first boat I am learning about...
  18. jhetrick55

    Replacing steering

    I need to replace the steering on my 1988 Sierra 165v. I have a 70hp Evinrude powering it. However the steering was not made for my boat and was installed before I bought it, but the cable it several feet longer than it should be and is coiled up and the steering pulls to the right. What I am...
  19. jhetrick55

    1975 Evinrude 70hp

    I boat my first boat last fall. Mostly the boat has run well with a '75 70hp Evinrude. But, it starts somewhat hard. Once it is running it seems to run fine. I have check the carbs and they seem like they're not the issue. But I did some digging and found very minor scoring in the center...
  20. jhetrick55

    Water and scoring in center cylinder - '75 Evinrude 70hp

    In the fall of 2016 I purchased my first boat - a 1988 Sierra, 16' Fiberglass fishing boat - and it came with a 1975 70HP Evinrude engine. I took it out once in the fall before I worked on the interior all winter in my garage. It started hard, but ran after I used the manual choke. The only...
Top