Search results

  1. Brock O

    95 Johnson 115HP - Budget Rebuild

    Few pics after pulling it down today...just need right socked to get rod caps off.....think i found the rings and piston pits, or the coarse ? seem the exhaust post was blocked....will have piston out and bore honed in a few days which will decide which way this budget build goes...
  2. Brock O

    95 Johnson 115HP - Budget Rebuild

    G,Day Gents...again Only been 4 years since a full rebuild and yet again it has thrown a ring...Phuk me!!!! Had no signs leading up to it...was running sweat, after failing to start with what i thought was a dying battery and then a dropped coil...has turned into a nightmare with the worse...
  3. Brock O

    95 model 115TLEOR Losing WOT

    Pulled the carbs last night, stripped them down to find a bit of black plastic under main the float valve between the intermediate fuel orifice. its the small black spec near the dart flight and would explain the fuel restriction at high RPMs. When we looked at that we thought fuel hose....hard...
  4. Brock O

    95 model 115TLEOR Losing WOT

    Gents, Last few trips the issue has occurred, It does have occasional idle problems but biggest thing is its losing WOT??sounds and runs smooth enough up to a point then just dies almost dead or to just an idle?then after a few seconds starts to take off strong again ?.I can plant it and...
  5. Brock O

    Boat Taking Water

    Cut the 1st hole last night closes to bilge and stuck the camera in, to walk on the deck its seems as solid as the day i purchased. Not sure about stringers, either there glass or wood covered in glass so the tanning could be from under side of floor ?? would it still be recommended to fully...
  6. Brock O

    Boat Taking Water

    Hello Gents, Few weeks back i started to notice the boat struggling at take off and occasionally leaning to one side. The deck is sealed as such, have had a few floor holes previously which i roughly patched. Silly i know but have just found the bilge does have a bung to the internal hull...i...
  7. Brock O

    1997 - 115Hp issues

    Hi Guys Hard one to explain. 1997 115HP 2 stk...TLEOR First started with the motor dropping a cylinder, we did find a coil had dropped and have since replaced it and another with a few leads, checked all the earth connections and wiring at power pack, new plugs etc since has been running...
  8. Brock O

    Blowing Coils - 95 Johnson 115

    Hi Guys With the motor rebuilt early last year all was going sweat until now, last month the motor dropped a cylinder in rough weather at low RPMs, once home we did a check off plugs and leads before finding a coil not reading right, this was replaced and all sweat again. last Friday heading...
  9. Brock O

    "0" Compression

    Hi Guys Progressing nicely, most of the motor was hooked up today except for intake and linkages, we managed to snap one of the small nozzles / nipples that screw to the block and intake manifold, 4 off in total on the motor with 2 located between the carby's, they feed oil I think to the crank...
  10. Brock O

    "0" Compression

    OK, yes found the wee hole easy enough after looking at the write end, and after reading the manual more carefully it clearly states all wee holes must face the fly wheel. So we now have all four rods and piston back in and the unit turning nicely, just waiting on a socket adapter before doing...
  11. Brock O

    "0" Compression

    Hi Guys Piston rings and gasket set has arrived, block has been machined with every thing ready to go, so have a few question before we start assembly. The factory manual i have is referring to inserting pistons and heads first before adding crank, to us this is ass about, we would put crank...
  12. Brock O

    "0" Compression

    Cheers Guys Pretty sure I've the correct manual but don't know how to confirm ? it dose cover most models 65 jet 115hp 90deg v4, 75 - 175 60deg V4/V6 and 120-300 90deg LV4/LV6/LV8. So pulled the motor down today, guy from machine shop had a quick look. I've order all parts today through...
  13. Brock O

    "0" Compression

    Cheers Guys, Getting some prices now on the gear needed, yes it will be new piston and rings through out, this does knock the price up but is the best way forward. Got 2 prices already with a big difference, could be sierra piston and ring set yet but still to decide after a few more prices...
  14. Brock O

    "0" Compression

    Well I'm sitting down having another Bourbon!! Did some one say BROKEN rings was a conmen failure! Well let me say firstly, the fact I didn't of all thing's perform a basic compression test is my own fault, don't know how many times I've read this.....To tell the truth the motor did sound all...
  15. Brock O

    "0" Compression

    Morning..late start due to a few drinks to help me sleep. Thanks heaps for the reply's, ill pull the head today and take some photo's, ill check the inspection hatch on the diagram and have a closer look today when I get to the boat. Emdsapmgr, previous problems were alarm issues, sometimes a...
  16. Brock O

    "0" Compression

    Hi Guys, Firstly great forum! I've been reading for a few months but now have to ask a question or two. This my second boat and of more age than the first so have been doing all work myself using the manual and this forum for info. Its a 1995 Johnson 115HP, 2 stroke model TLEOR, hopefully I'm...
Top