Search results

  1. Lake time

    5.7 wont get to wot

    i have a 1985 murcruser 300 tempest this weekend it ran great for an hour at 3800 rpm and she started sputterng and cant get it above 2500 rpm and i smelled gas when that hapend 4 plug wires are a bit losse the last time it had a tune up was 05 so this weekend im doing plugs, wires, cap, rotor...
  2. Lake time

    ? On rebuild used outdrive

    I just bought a used outdrive that has been sitting for a few years it's a 1988 1.47 1.50 ratio is just cracked it open to day all seals seem great needs a new pump I let the old oil out it had a little water in it I'm thinking it just condensation format sitting getting warm and cold but was...
  3. Lake time

    Need reviews on se106

    I am replacing my 1985 apha one gen 1 drive and was looking for reviews on them tissue going to be put to a 1985 5.7
  4. Lake time

    Surge brake help

    I have a double axle trailer with a 12000lb rated surge brake master cylinder just put all new baking system on free backing the issue I ran in to was the drums where dragging and popped my bearing buddies of going down the road the grease was boiling now mind you I had the shoes adjust all the...
  5. Lake time

    Prop help michigan prop 031051

    I have a michigan prop 031051 it does not have diameter and pitch stamp anywhere I'm trying to find out the dia and pitch of the prop to get a new one it's aluminum and it's on a carver montango 2657 with a 1985 5.7 merc max remember 4800 with ano sei out drive 1.47 gear when on plane 13 people...
  6. Lake time

    Lake erie cruise to ceader point and put in bay

    We have a 1985 carver montego 26 we are taking our first cruise on it for our honeymoon we are going to ceader point and put in bay plan on spending 2 days at cp and 2 days at pib we are coming from erie pa I was wondering if any one has experienced any of the marinas out there and if you guys...
  7. Lake time

    Bottom paint for trailer boat

    I have a 1985 carver montego 2657. We bought it in April and the bottom has antifoulin bottom paint. It used to be wet dock all every year up to no I have no plans or nor do I want to every dock it is the address bottom paint I can use that won't rub on my bunks
  8. Lake time

    Trim gage not working

    I have a 1985 carver 2657 5.7 murccruser alfa one gen one my trim gage is not working where is the sender and could it be out of adj what should I look for and where do I start
  9. Lake time

    Help with winterizing

    I have a 85 carver 26 foot the with no outdrive the motor is a murccruser 5.7 how do I winteriz with no out drive
  10. Lake time

    water sports can I do it

    I just finished redoing a boat I got this summer it's a 1964 14 ft mfg niagra with a 1963 40hp jonhson super seahorse it does 32 mph on the water I was wondering if that will be enough to water ski, tube, and maby wake bored, just wondering if it can do it
  11. Lake time

    1963 40hp johnson no reverse

    1963 40hp johnson electronic shift I was out this weekend fishing and backing up from the dock just fine put it in forward and went across the lake just fin but when I went to back up to the fuel dock it picked up rpms but did not move forward works just fine I'm thinking it might be the magnet...
  12. Lake time

    1963 40 hp jonhson not getting to wide open throttle

    I hav 1963 that won't reach wot it's getting spark to both cylinders I put a new float in the carb compression is outstanding new points coils and condeners she just not reaching the full rpms it's on 14 foot mfg niagra it gets me moving about 10 mph pr plain that's it it's got a 12 pitch prop...
  13. Lake time

    1963 40hp johnson running on one cylinder

    Ok I have run out of ideas I have a 1963 40 hp Johnson super sea horse elictric shift only running on one cylinder. It's running on the bottom cycling the compression in the motor is good it's about 110psi per cylinder I've put new points condensers plugs boots wires on it and it's still running...
Top