Search results

  1. MickLovin

    90hp 6 cylinder 2 and 3rd carby leaking

    Hi, my friend has a mariner 90hp 6 cylinder which has fuel leaking out of carbies 2 and 3 when primed, I am used to the old Chrysler carbies so I am not sure if he has a float problem or needle and seat problem as the primer will not get hard, he also has an issue with cdi #1 as it isn't...
  2. MickLovin

    Lucky new force 125 owner ;) first outboard 2 stroke jet engine for me.

    From what I have seen of the jet drive, they have a pump and impeller not much different to normal, well thats what the Johnson's look like.
  3. MickLovin

    94 force 120 water pump problem

    I have heard of the side exhaust gasket causing this problem, but others here may have other causes.
  4. MickLovin

    Still mourning my 100HP Chrysler 1979

    Ok, here we go again with my sad story, it has been 3 weeks now, but the last 2 weekends it has been raining cats and dogs with the odd cow joining in, I didn't notice how much I missed old (I will call her Miss Grunty) Miss Grunty, till I saw the river and how glassy it was with a beautiful...
  5. MickLovin

    75hp is very slow

    Re: 75hp is very slow The compression in the crank forces the diapragm in and out, therefore pulsating the pump into pushing the fuel towards the carbies, if your valves aren't working this could also be the problem. take your line off to your filter and have someone crank the motor while you...
  6. MickLovin

    whats wrong with my kicker ?

    Re: whats wrong with my kicker ? should be a few inches above the water pump housing which is located at the LU top join. Agree with Nordin That picture is of a 1984 - 1995 after that they don't seem to have t'stats
  7. MickLovin

    75 hp Chrysler I.D. and questions.

    Re: 75 hp Chrysler I.D. and questions. That is my 76 model with a two piece gear box, the one in the last post was my 80 model, notice the cowl difference, they went away from style to a cowl with a f.....g sticker LOL, the 76 model cost me $200 and it actually ran better than my 80 model...
  8. MickLovin

    75 hp Chrysler I.D. and questions.

    Re: 75 hp Chrysler I.D. and questions. Hey mate, I loved my old 75HP it was an 80 model, but yours looks bare down at the prop, get a nose cone and flare, just looks better LOLOL
  9. MickLovin

    Force 90 Carb Swap

    Re: Force 90 Carb Swap As I am unsure of what your model numbers are this is waht I found off iboats parts catalog That's from a 90hp 1990 no particular model number, That's from a 90hp 1997
  10. MickLovin

    Chrysler Tachometer Question

    Re: Chrysler Tachometer Question Hi Andrew, one will be a negative and the other will be a signal, which will be the white cable from your motor which is normally either on the ignition switch or taped off in the cable loom, the only problem is I am sure which terminal on this is negative and...
  11. MickLovin

    1979 45hp Chrysler Electrical issue.

    Re: 1979 45hp Chrysler Electrical issue. Could be either your stator,which by the sounds of 6v it possibly is, but I am also unsure what reading you should get when you put an ohm meter on it. and 11.5 volts is more than likely your battery voltage as it should be charging at 1000rpm and...
  12. MickLovin

    Sad Tale of a 100HP Chrysler

    HI Guys I have a sad story for you, after playing with my boat for about a year and finally, after all this time getting the motor running Bewtifullllz and the boat all freshly painted and looking like a xmas tree at night with all my LED lighting LOL. I am selling it sob! yes that's right after...
  13. MickLovin

    Force 40Hp will not start

    Re: Force 40Hp will not start I have attached a copy of the parts for your ignition assembly and will try and find a schematic, but others here will give you a better indication of what may be wrong as I am not familiar with the force engine of this age. Did your mechanic friend do a check on...
  14. MickLovin

    100HP Chrysler with 17" prop

    Re: 100HP Chrysler with 17" prop No problems mate, the tacho came with a chart which has a column for rpm. I will post it now.
  15. MickLovin

    motor shaking at mid range

    HI guys took my motor out again today with the 17" prop, could still only get the motor to 4500RPM with the tacho synced, also was only getting 38mph. I have a strange feeling it is a carbie problem.
  16. MickLovin

    Chrysler Tacho Sync

    Hi all, just did a sync with my handheld and my onboard and found the onboard to be way out, on it's instructions it show a setting of 6 @ 6000 rpm for a 12 pole, I had mine set at 5.5. When I sync it with the handheld my onboard was showing 750 but my handheld was showing 950 - 1000. To sync my...
  17. MickLovin

    chrysler 140hp help australia

    Re: chrysler 140hp help australia This was my Fletcher Arrowflyte 14.5ft, with a 115HP 1984 Suzuki on it, the only difference with my suzuki besides bores etc was it had 4 carbies, fn thing was hard to sync. I did finally have this motor running beautifully, pulling 50+ mph, but it would start...
  18. MickLovin

    100HP Chrysler with 17" prop

    Hi guys it's me again, some good news and some bad news here I am afraid, the good news is, I finally got my boat on the water, bad news was it only would get to 36mph and around 3 - 4000RPM, it was shaking a bit, but only shaking when it was mid range throttle and then a bit lower too idle...
  19. MickLovin

    Force 120 1996 lost power to trim and ignition

    Re: Force 120 1996 lost power to trim and ignition I would try and trace the wiring to both the relays of the tilt trim and the positive to your ignition switch, to see if there is either an inline fuse or junction. Do you have a volt meter? Looks like that from the diagram the tilt trim relays...
  20. MickLovin

    How to locate cyl#1 trigger under flywheel Force125?

    Re: How to locate cyl#1 trigger under flywheel Force125? Don't know if this helps Let us know what year or model and what you are trying to achieve or repair.
Top