Search results

  1. C

    Gear Oil Leak Into Bilge Area After Rebuild

    I have a Mercruiser Alpha 1 Gen 2 in my 1998 Maxum. I have noticed gear oil pooling in the bilge of my boat and thought it was coming from the reservoir. I put new seals on it to verify if it was the issue or not and filled it up again only to find it had leaked out again the next day. The...
  2. C

    Clarification Needed on Shift Slide and Lever - Reinstalling Drive

    I am attempting to re-install my Alpha 1 Gen 2 drive unit and had placed it in Forward before disassembly. Now I'm afraid that I may have moved the lever on the lower unit and may have moved the lever and shift cable slide piece. I'm not familiar with these parts very much and saw that the...
  3. C

    Unknown Wires Left After Engine Rebuild 1998 5.7 Mag

    I didn't do the best job labeling some of the wiring on my rebuild of a 1998 Mercruiser 5.7. I've got most of the wires connected on the engine harness except for a few. I haven't had any luck finding them in the diagrams in the manual so I thought I'd see if someone on here could help 1. Black...
  4. C

    Sea rayder leaking oil at base of powerhead sport jet 90hp

    I rebuilt the engine last year and I am trying to get all of the kinks worked out of the boat. Went out yesterday for the second time on the boat and noticed it was revving up fine but it wouldnt get up to speed. Lifted engine bay cover and noticed fuel/oil mix pooling in the valley of the boat...
  5. C

    Question On Setting Timing 1993 90HP Sportjet

    Somehow the nut and screw on the trigger arm accidentally came loose on my boat recently while breaking in my rebuild. Unfortunately the trigger arm got moved around some so I'm unsure if the timing is correct. The boat was running around 3000 RPMs at idle when I had it at the dock and I wasn't...
  6. C

    Need Help Identifying the Model of This Baja-

    I am looking at a Baja boat at an insurance auction. I'm not too familiar with their models so could someone tell me the model name on this boat? Trying to determine a value before bidding. Thanks! HIN VIN: AGCC4836G394
  7. C

    Spark is Back But Engine Won't Turn Over- 90 HP SportJet

    Thanks for the suggestions and words of encouragements from the NO SPARK thread http://forums.iboats.com/showthread.php?t=577914 NO SPARK thread. I replaced the switchbox with a used working CDI unit and I have spark on all three cylinders. Spark is present with yellow/black wire disconnected at...
  8. C

    No Spark 1993 90hp Force (Sportjet)

    Re: No Spark 1993 90hp Force (Sportjet) Yes I have the adaptor box thing installed. Here's an actual picture of the side of my engine. One thing though that I need verified: I had an extra ground wire that I ran to one of the bolts to one of the fuel recirculation ports. I am farily...
  9. C

    1993 Sportjet 90hp- No Spark

    Re: 1993 Sportjet 90hp- No Spark I have the red stator with the Green/White & White/Green wiring plus the two yellow wires. When I tested the Green/White & White/Green wires, they measured 705 or 680 ohms. On one of the CDI Troubleshooting Guides, it says that the reading should be around...
  10. C

    No Spark 1993 90hp Force (Sportjet)

    I have a 1993 Sportjet 90hp engine in my Sea Rayder. It has no spark at any coil. The engine will turn over but i have no spark on any of the three plugs using an inline spark tester . I have attempted to use the following links to try to diagnose the problems. It does have the red stator kit...
  11. C

    1993 Sportjet 90hp- No Spark

    I have a 90 Sportjet that I originally purchased with low #1 cylinder compression. The engine would crank when i bought it but ive never heard it running. After rebuilding and installing the engine, I can't get it to fire. I have 12+ Volts throughout the starter system as tested by my multi...
  12. C

    Sea rayder sport jet 90-need advice on parts to replace along with piston swap

    Re: Sea rayder sport jet 90-need advice on parts to replace along with piston swap Yes it cut some nicks out of the cylinder. I am wondering if 10 Over will be enough. Here are some pictures of the piston and of the cylinder wall that the piston was taking out of.
  13. C

    Sea rayder sport jet 90-need advice on parts to replace along with piston swap

    I just recently bought a 1993 Sea Rayder. It had low compression on the top cylinder (15-20psi). All other cylinders showed around 130+ I believe. Engine is apart and there is several nicks out of the piston around the rings of the top cylinder piston. After I get the measurements of the...
Top