Search results

  1. E

    1989 evinrude banging

    Hi everyone my problem started a while ago with doing water pump and I got the shift rod length wrong so I fixed the shift rod length but the engine would bag as if I was hitting a log at 4000rpm so I bought a clutch dog thinking it could be slipping. I have the gear case open thinking that...
  2. E

    1988 edson 17" bowrider transom spongy

    hi everyone on here took my 1988 Edson 17" 110hp outboard to shop to get the engine bolts resealed cause of a leak I have been chasing.so the shop tells me they cant seal it cause the transom is spongy so now I am planning on replacing the transom I am assuming the stringers will need to be...
  3. E

    resealling engine mount bolts

    the engine is a 1989 evinrude 110 hp. is it possible to reseal these bolts without removing the engine from the transom ? and do these engine have the lift rings built in or do the have to have the lift ring tool?
  4. E

    tach help

    today I went to buy a tach for my 1989 110 hp cause mine doesn't currently have 1. the person at the counter told me I should contact evinrude to see if there's a harness to buy so I can install a tach . I was looking at the Teleflex. any help would be appreciated
  5. E

    shift rod length need help

    ok I looked threw the secret files on here not sure which 1 is for my engine I made few mistakes already I have a 1989 110 evinrude not sure which shift rod length is right for my engine ? any help would be appreciated
  6. E

    1989 evinrude 110 outbord control cable questions

    so I had the lower unit off today and now I have it mounted now. I need to adjust the throttle cable because I moved the cable adjuster. I didn't move the idle screws at all and before I moved the adjuster it idled great. can I put the idle screw up against the stopper and adjust the cable to it...
  7. E

    1989 evinrude exhaust seal

    I redid water pump and found that that exhaust seal needed replaced I seen on here that people are sealing them in place for alignment. what sealants can I use ? or how can I install the seal?
  8. E

    oil or grease center of axle

    today I notice oil or grease on the center of the axles. its not running along the axle and stopping there looks like its starting there and stopping there. the trailer is a 1989 calking not sure on the spelling no brakes has 17 foot ski boat on it. any advise how to fix or what the problem...
  9. E

    shift rod question

    i have a 110 hp 1989 evinrude i did the water pump the other day and the shift rod turned on removal so i turned it back to where i thought it was. so i put it back together it goes into forward reverse and neutral no problem. my question is if the shaft were to short would it allow the engine...
  10. E

    edson1988 hp upgrade question

    i have an 1988 edson xr-17 it has a 110 evinrude on it from everyone ive seen online and contacted these boats dont have capacity plates on them.woundering what it could safely handle the hull style would be compairable to the cheeta boats. any help would be appreciated.
  11. E

    loose windshield

    hi everyone i have a bowrider and it has the tipical bowrider windshield.while i was on my vacation my windshield lost a screw and some of the windshield fell apart.i put in a new screw but it backed out again. the screw that fell out is the 1 that the glass in place not the 1s that hold it to...
  12. E

    1988 110 evinrude vro/speedo/tach question?

    ok the speedo on my boat doesn't work it is the pitot type and the speedo and the tach reading come off off the same gage so i was wondering if because it is the water preasure type that it wouldn t be acurate to begin with.if its not acurate would the motor be set up to reach a safe max speed...
  13. E

    transom drain plug

    hi im new to the forum and im having a problem with my drain plug i have the brass type with the square end to put a wrench on it. ive noticed that it is slowly seeping in maybe a teaspoon for about 8 hours of fishing ive tried replacing it .what else can i do to test it or even replace the hole...
Top