Search results

  1. S

    90HP J90TLETS - Flywheel torque spec

    Can anyone tell me what the correct spec is for the flywheel nut?
  2. S

    1993 Johnson 90hp - Oil queries

    You guys helped greatly sort some issues a year or so back so I'm here again to find some answers. I've got a 93 Johnson 90hp v4. It seems to be that its using more oil than it should. I'm suspecting its about double (I've only just started noticing its excessive) The remote oil tank doesn't...
  3. S

    1981 J8RCIC Johnson 7.5 No water from tell tale

    hey guys, i seem to have resolved most of the issues with my 90hp thanks to the help from here. I just fired up my 7.5 to test it before going to the lake next w.e and it started fine but the tell tale was spluttering water, no steady stream. It's not progressed to only blowing air and no...
  4. S

    Johnson 90HP - Wont rev to potential - WOT

    J90TLETS Will idle ok and seems to run well but when you go full throttle it doesnt seem to rev out all the way. Took it out when it was choppy yesterday and it was near impossible to get on the plane. would only rev to 3200rpm full throttle and pull about 12mph into the chop, riding the wave...
  5. S

    93 Johnson J90TLETS - Wont prime fuel

    If its not one thing its something else lately with this motor. Im close to pouring gas on it and setting it alight. Please help It's decided it wont prime hard. Pump the primer and you can see gas through the fuel filter on the motor but where it goes up into the intake manifold it was...
  6. S

    '93 Johnson J90TLETS - Lower Engine Cover removal

    Hey guys I want to try and drop the cover so i can get the shift rod out and clean it up as its binding. This design unfortunately isnt a split cover so i will only be able to drop it a bit but i think it will be ok. Anyway so ive removed the cover below this and then the 2 bolts from the...
  7. S

    6 hole fuel sender replacement options

    Re: 6 hole fuel sender replacement options Thanks for the info guys. When i say the original unit is rusted up i mean its now 1 piece of rust, looks like its been laying in salt water since the titanic went down, in fact i think the titanic is in better condition. The fuel tank is a large in...
  8. S

    6 hole fuel sender replacement options

    I've just removed a rusted out sender from my boat. It has a 6 bolt flange. 60mm diameter and equal bolt spacing of 30mm. Tank hole is 45mm. I found a VDO adapter to run a 5 bolt flange sender but the hole for that is 54mm so its not going to work. Anyone know if you can still get a 6 bolt...
  9. S

    '93 Johnson J90TLETS - Shift Rod issues

    Finally got my boat in the water with the old man and it wouldn't get into forward or reverse. We took it out and checked the cables and the shift rod. I had previously removed the lower unit to replace the water pump. From some youtube videos i've seen the shift rod should move forward and...
  10. S

    Strange leak from prop

    I have a '93 Johnson v4. I recently changed the water pump impeller, housing and some gaskets. motor ran fine and tell tail was all working. had a guy check it out who recommended i do the headgaskets. Just finished those, replaced the water deflectors and the exhaust housing gasket. Motor...
  11. S

    Johnson 90HP head gasket replacement

    J90TLETS - 1993 Johnson 90HP v4 Ive gotten a complete powerhead gasket set just in case there are extra things to replace. What i wanted to know was what the head bolt torque settings are and if there are any other bolts that need a specific torque setting? Any other tricks/tips would be great...
  12. S

    Yet another tilt electrical issue

    I have a 93 Johnson V4 90HP. Its been sitting at my old mans unused for about 7 years before i convinced him to let me use it. The tilt was originally only going up, i switched the relays round and it would go down. Brought a new relay but it was wrong, 2 pins were round the wrong way. Went...
Top