Search results

  1. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    Thank you. Will try to look for the relay.
  2. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    What do you think about cutting the new grommet to run the wires through and marine caulk after?
  3. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    LOL. LOL. Ok thank you. That way seems to be the safest way.
  4. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    I was planning on cutting them and use butt splice connectors. Then heat shrink. What do you think?
  5. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    I know where to disconect the other wires accept for the blue & green trim wires. I don't think I can disconnect at the trim motor. Maybe at the relay? But don't know where that is located at.
  6. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    Thank you for the reply. Just the grommet.
  7. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    Where do I disconnect the trim wires to feed them through the rubber grommet?
  8. N

    Garmin Striker Plus 7SV Transducer Disconnected Error

    So I shouldn't connect the wires according to the chart? I was going to connect the wires according to their color codes. I was going to connect the blue, black, and shield wires according to their colors on the unit.
  9. N

    Garmin Striker Plus 7SV Transducer Disconnected Error

  10. N

    Garmin Striker Plus 7SV Transducer Disconnected Error

    I am tryin to hook up the Airmar External Transom Temperature Sensor T80 10k ohm Analog Thermister as a fix but do not know how to wire it. There are 3 wires on the temp sensor. They are blue, black, and metallic. What wires on the unit do you connect these to? A wiring diagram will be very...
  11. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Would it be okay to use a vortec block and switch over the cam and the crank from the non vortec?
  12. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Can I use the Automotive vortec heads or do they have to be Marine? What's the difference?
  13. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Will I still be able to use my current 14 1/2 x 15 SS 4 blades prop once the motor is converted to Vortec?
  14. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    My current 4.3 has roller cam and non balance shaft block, will this affect the conversion to Vortec? I have already purchased the Edlebrock 1409 4 bbl Performer carb and the EDL-2519 Performer intake from Summit Racing as Scott suggested.
  15. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    If converting to Vortec, do I need to change my current crank to a Vortec crank?
  16. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Just in case I have to get a complete turnkey motor, does any one know if this motor will bolt in w/ my current 4.3 or does the engine mount needs to be modified? Thank you for all the advice given. Mercury Mercruiser Marine - PLUS Series 350 MAG MPI Alpha Bobtail Marine Engine (#863611R11)
  17. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    I am converting to Vortec and currently have a 2bbl MerCarb. Is it better to switch to a 4 bbl for more horsepower or can the same be achieve w/ my current 2 bbl? Thanks.
  18. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Can anyone help with finding Felpro cylinder head and intake gaskets only and not the whole set for the vortec 4.3?
  19. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Are the cylinder head gaskets for the 4.3 non-vortec and vortec the same?
  20. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Thank you Chris for all the info! Awesome!.
Top