Search results

  1. R

    Slipping out of gear?

    http://youtu.be/Fm5uKBig4lk?t=3m19s
  2. R

    Cowl Seals, how are they installed?

    I need to replace the seal in a 25002c. Were they stapled on in the factory (going through aluminum)? Or were holes pre-drilled for the staples? seems like a lot of work...
  3. R

    Sears Ted Williams 9.9 217-5871-0

    Two things. I have weak spark, both cylinders. Where do i go from here? what output voltage do i need? Next thing, the oil fill screw is missing. It looks like the threads on the case aren't original and re-tapped. i get a weird size according to my thread gauge, 13 thread pitch, it's about...
  4. R

    Steering Handle Shift Kit for 6-25hp

    Anyone use this shift kit? I need to know where the lubrication points are located. I don't have the instructions.
  5. R

    Obsolete impeller 47-26554, any alternatives (or sources)?

    Need a new impeller for mercury 1,59X,XXX
  6. R

    1974 Johnson 40 HP Shifter Lock Engineering

    There isn't a depression on the shifter lock for Neutral, instead it's on a plate. My motor will not stop at N and just goes from F-R or R-F. This is one expensive part change that wasn't necessary, so how do I adjust it?
  7. R

    1996 Evinrude 25 BE25KLEDC no spark

    I did not have spark on any of the cylinders. I know my stator passes all the diagnostic checks, i replaced the powerpack with a new one and i still don't have spark.
  8. R

    Testing Optical Sensors

    I have no spark on a 1996 25 hp 3 cyl. Evinrude (BE25KLEDC) The stator passes the output tests but nothing from the power pack. The power pack is $350 and the sensor is $150. There is no troubleshooting test in the service manual for the sensor. All i can tell is the encoder and sensor are...
  9. R

    DIY Flywheel holders

    I need a cheap flywheel holder the remove and install flywheels, i would need to be able to torque the crankshaft nut to 120 foot pounds. I could make an OMC flywheel holder that is illustrated in the service manual i have, but buying a metal hole cutting bit for $20, to be used only once...
  10. R

    1996 Evinrude 25 BE25KLEDC stator diagnosis

    i performed the output tests for the power and charge coils. Both grounded tests returned no signal on the voltmeter. Output tests returned no voltage for both the power and charge coils. Resistance test for the power coil was 8 (forgetting the scale) it should have been at least 57. Am i...
  11. R

    35 hp Johnson Piston and ring replacement.

    i'm working on a 77 35 hp johnson, it had <20psi compression on both cylinders after i installed a new powerhead gasket kit and head gasket. The cylinders walls are in excellent shape, as well as the pistons. I added some oil to both cylinders and got 140psi on the top, and still <30 on the...
  12. R

    No Spark (1996 25hp Evinrude 3 cyl )

    i tried starting this motor without the controls hooked up. It doesn't spark on all 3 cylinders. It is wiring for remote start/systems check. I am just wondering if i do indeed need to hook it up to controls or is there a failed electrical component?
  13. R

    Has anyone attempted this?

    On the low tension magnetos with 1 traditional coil under the flywheel supplying power for 2 external ignition coils, what would happen if a second coil mounted on the armatureis rigged to supply power to the battery? has it been tried? How many amps could a traditional ignition coil output?
  14. R

    OMC battery cables

    i want to know the gauge of the battery cables used in wiring harnesses for 25hp Johnnyrudes, 69-76. I am attempting to repair the control wiring harness, which is obsolete.
  15. R

    3 cyl. 25 and 35 hp Johnnyrudes

    where is the HP difference? it seems like these motors would perform a lot better than the traditional 2 cylinder motors. I am not looking to tweek the motor i have, just interested in the hp difference
  16. R

    Removing decal on decal

    bought a motor, 1996 E-rude 25hp 3-cylinder, well the owner slapped a big Rage Tail decal on the back of the hood, covering the evinrude decals. Is there any way to salvage the evinrude decal while removing the rage tail decal?
  17. R

    OMC tools, question

    i am looking for terminal connector tools, one installs terminals on those black plastic clips that usually only have one connection. these are found on kill switches and sometimes ignition coils. the other type installs terminals in the plug type, either for the main wiring harness, or...
  18. R

    Johnson PO-15 questions

    Does this motor have F-N-R? spark advance lever? I ask because looking at a 1949 brochure, there is a lever coming from the magneto, but there is another lever on the throttle bracket that controls something under the carburetor. This is the picture in the brochure...
  19. R

    Matching Color of a custom paint job

    Well, i acquired a motor from a guy who restored it and used a really nice looking color. A few parts weren't repainted and i'd like to make everything one color.. problem is he told me it was custom mixed and he didn't have a paint code for it. What is the best way to match the color without...
  20. R

    Obsolete part for 1976 Johnson 35 hp

    I had ordered a pair of water deflectors (318357) through my local dealer, he calls back today and says BRP told him this part is now obsolete. Say it is obsolete, is there an alternative? Parts from a later model 35 hp, but it looks as though in 1978 there are 3 deflectors instead of the...
Top