Search results

  1. D

    Evinrude Lark Tilt Possibilities?

    Hello all, I have an Evinrude Lark 40 HP. The model #35520 and the serial #06070. I believe this motor is a 1960. I was wondering if anyone knew of a power tilt/trim option that one could bolt onto this motor? I know of the CMC option but don't like the added weight and I'd like to keep somewhat...
  2. D

    Retrofitting tilt/trim to a 1960 Evinrude Lark 40 hp

    Hello all. I was wondering if anyone has any input on retro fitting a tilt trim set up to my 1960 40 hp? I was wondering if a 1970 60hp 60073d evinrude tilt/trim assembly would work? Any help would be greatly appreciated. Also I'm trying to spend less than the CMC model. My model number is...
  3. D

    Throtle/Gear shift box for a 1960 Evinrude 40 hp lark

    Hello there, I was wondering if anyone knew where I could get a throtle/gear shift box for a 1960 Evinrude Lark 40 hp? Or will any one work? The one I have now doesn't seem to be working properly with the proper length cables for the motor and everything. Thanks.
  4. D

    1960 Evinrude lark 40 hp leaking lower unit oil somewhere?

    Hello all, I was wondering if anyone had any ideas about where I could be leaking my lower unit oil to? I have checked the lower unit for cracks and I seem to be good there. Anyone know anything about the drive shaft seal on this motor? I.e how much would it cost part number? or any other places...
  5. D

    Parts for a 1960 Evinrude 40 hp

    Hi all, I'm wondering if anyone knows where I can get a drive shaft seal for a 1960 Evinrude 40 hp motor? I posted something a while back about loosing all my lower unit fluid every time I drove the boat and someone suggested the drive shaft seal is bad. Any suggestions? Thanks!!!
  6. D

    Power trim for 1960 40hp Evinrude

    Hi all I was wondering if any of you have seen anyone retrofit power trim to a 1960 - 1970 40 hp Evinrude? I have a perfectly good running motor, I'd just like to get some trim for this motor. Thanks for any help. -Dickinson
  7. D

    1960 40hp evinrude

    I have a 1960 40 hp evinrude that seems to be loosing all the lower unit oil in it everytime I run it for a few minutes. I cant tell where it's coming from? Any ideas? It didn't start doing this until it came back from being stored outdoors this winter. Something cracked? or just a gasket...
  8. D

    what year and lark # is my motor

    It's a 1967 I think: the serial # is 06070 and the model # is 35520. Thanks!!!!!
  9. D

    Fitting an Evinrude Lark with power trim, Possible?

    Hello all, I'm looking to find out if anyone knows where or how I can retrofit power trim to my late 60's to early 70's evinrude lark lll motor. Thanks for your help!
  10. D

    Tilt/Trim

    Has anyone ever tried to retrofit a 1969 evinrude 40hp outboard with some sort of ***/trim? Any help would be appreciated. Thanks
  11. D

    1969 Evinrude 40 hp problem

    I have a 1969 40 hp evinrude outboard motor that I have gotten excellent feedback and help on getting it going, I need your help once again. I Have had it running good and decided to put a little sea foam in a tank and ran it through and it was all good. Then I put the right amount of oil in...
  12. D

    1960 40 hp evinrude questions

    Hi all, I've almost got all the issues with this motor worked out thanks to you all. I was just wondering if anyone knows if you can cut out the vacuum cut out switch on this motor. I have filled the tank half full for all my tests and it has been working great. I went to take it for a weekend...
  13. D

    1960 evinrude 40 hp with no top speed

    I have a 1960 40hp evinrude that has not top speed at all. I pin the throttle and it goes a bit faster than an idle but not really more than 1/4 speed for a 40 hp. I have good spark on both cylinders as well as fuel coming though the pump. Carb has been cleand and throttle is pinned inside the...
  14. D

    1960 40 hp evinrude hood parts

    I'm looking for the parts to attach the bottom rim and the top cover to my 1960 40 hp evinrude. I took them off to paint the cover and lost them. Now I have no way to attach the cover to the boat. Any ideas?
  15. D

    What prop should I use?

    I have a 1960 40hp evinrude outboard motor. I need to get a new prop for it and don't know what size or where to find one as well.
  16. D

    1960 40hp evinrude outboard motor

    I need to know if there is any way to bypass the mercury switches on the throttle? I think they may be failing making it nearly impossible to get my motor started. Also I still have the question about the 1/8 power issue. I have good spark on both cylinders carb has been cleaned as well as the...
  17. D

    Homemade transom bracket?

    Anyone have any pictures or guidelines for building one of these things? I think I could make one for less than $40.00 like you'd pay to buy one at the store.
  18. D

    1960 Evinrude 40 hp high speed problems????

    Hi all. I was wondering if anyone had any info they could share with me about my motor. I have a 1960 40hp evinrude that runs great low end but when I advance the throttle to full power the motor only goes to about 1/8 of full speed. Both cylinders have spark, both have similar compression at...
  19. D

    1960 evinrude 40hp motor running 1/3 power

    Hey all, I need some help. I have a 1960 40hp evinrude and when i have it at full throttle it seems like it is only running about 1/3 speed or power. Any thoughts? Thanks for your help!
  20. D

    ignition for a 1960 40hp eveinrude

    I'm looking to see if anyone knows what model number or where I can find an ignition for a 40 hp 1960 evinrude outboard. Thanks for your help.
Top