Search results

  1. G

    Trim Cylinder Spacer Kit Prep

    All, I need to install trim cylinder spacers in the rams of my Alpha I to avoid it hitting my swim platform when raised up and have questions: 1. Will one set of spacers be sufficient or do I need to order more to stack spacers in the cylinder? 2. Do I need any special wrenches? I saw a...
  2. G

    Rebuilding Engine/sunbathing Hatch - Need Wood or Other Recommendation

    Hi Experts, I am in process of rebuilding my boat's engine hatch/sunbathing platform. It has a fiberglass support piece but also has/had plywood pieces that have rotted due to water getting past the vinyl and soaking the foam and wood. I am looking to fix this right but do not want to over-do...
  3. G

    Tilted Drive Down - Oil Came Out - Now no leak??

    All, My bro in law tilted his drive down from being up and some drive fluid came out of the small vent holes. He has left it down and prepared for more drive fluid to come out, but nothing has shown up after a few days. Any ideas on where this leak might be? Why isn't more coming out? TIA
  4. G

    AQ260B Manuals

    All, Is there a link (4shared, etc...) for a 1986 AQ260B service manual? I have seen links to the owners manual. I need the shop/service manual. Thanks all!
  5. G

    How do I match the gel coat of my boat?

    Guys, Is there a part number or something I can use to match the gel coat of my 1994 VIP 2012? Help!
  6. G

    Buying Swim Platform Need to Match Hull Color

    All, I have a 1994 VIP and am adding a swim platform. What is the best way to provide the vendor with a color match so they can match the hull? They have suggested the use of the Home Depot Behr colors charts to get close. Is there a better way? Can I reach the manufacturer (I don't think...
  7. G

    Polishing - color on pad

    All, I am applying a Meguiar's 49 Heavy Oxidation remover to my hull with a polisher to remove some minor scratches. Should I be seeing some of the color from the hull on my wool pad? I have not been applying much pressure. Jason
  8. G

    Diff Between Merc and Quicksilver HP Gear Lube

    All, Is there a difference between Mercruiser High Performance Gear Lube+ and Quicksilver High Performance Gear Lube? I see a "plus" mark next to the Mercruiser branded lube.
  9. G

    Info or Book on Building an Engine?

    All, Is there a book, link, or FAQ, etc... on how to build a marine engine?
  10. G

    Replace 305 (5.0LX) with 350 (5.7L)

    All, It's another post on repowering, so I apologize ahead of time. Here's what I need to know: 1. Can I use the parts from my 1994 5.0LX engine on a marine 5.7L long block? 2. Can I use the same Thunderbolt Ignition? 3. Is it worth going to a 350 versus the gain in weight of the...
  11. G

    Minor Adjustment to Streering

    All, Is there a way I can adjust the power steering on my 1994 Merc? When the steering wheel is in the straight position the drive is angled slightly to starboard causing the boat to go to the right. Do I adjust the power steering unit? Do I adjust the rack up near the steering wheel? Thanks.
  12. G

    Merc Standard Spark Plugs

    All, I have found that this is a fairly common discrepancy. I too just pulled my plugs out of my 1994 Mercruiser 5.0LX (Thunderbolt IV) engine to find that they were MR44T and not MR43T. The service manual and my owner's manual call for MR43T. Here's a similar thread...
  13. G

    Merc Gear Lube Reservoir Levels

    All, I just had my the upper and lower units professionally resealed. I took it out over the weekend and ran it normally. When I started I had lube at the fill line. However, I checked it one morning and it was about 15% less than when I started. I then ran it for a few minutes and ran it...
  14. G

    Merc Loose Harness Ground Wire

    All, I found a loose wire that is part of the harness. It is with the set of wires that connect in and around the 50A circuit breaker. This is a 1994 Mercruiser 5.0LX with Thunderbolt IV ignition system. I am almost certain that it is a ground wire. However, I don't know why it is...
  15. G

    Slight Vibration on Left or Right Turns

    I understand this is a common theme in these forums. However, is there an appropriate post for this condition? The boat runs great going forward. However, when I turn left or right, I feel a slight vibration. Is this the gimbal bearing or universal joints or both? I will certainly find out...
  16. G

    Mystery Vacuum Hose on 4MV

    Where do you think a hose goes that connects to this port? I have a Rochester 4MV with an unconnected hose end that is capped off. It is not the sight tube and not the vacuum break. See attached pic.
  17. G

    New Impeller, then Overheat Warning

    All, I did the right thing by getting the Quicksilver impeller and seal kit for my Alpha 1, Gen II. I replaced it and put the lower unit back on, etc... http://forums.iboats.com/showthread.php?t=391127 I put the muffs and water on (half-flow) and it seemed to run great. After 5-8 minutes the...
  18. G

    Mercruiser Rochester Quadrajet 4MV Filter

    All, Is there an acceptable inlet fuel filter that I can get readily at an auto parts store for a 1994 Quadrajet 4MV that fits a Mercruiser 5.0LX? The service manual says that the carb is a Rochester 17080565.
  19. G

    Alpha 1 Gen II Water Pump V-Ring

    This relates to my earlier post on replacing a water pump http://forums.iboats.com/showthread.php?t=391107 I am going to order this kit to do this...
  20. G

    Alpha 1 Gen II Water Pump Repair Kit

    All, Now that I know I have a Gen II sterndrive, I want to replace the impeller, gaskets, and seals for the water pump. The p/n on the impeller is 47-43026. Is this kit an acceptable replacement...
Top