Search results

  1. M

    Evinrude 40 hp trim removal

    I really dont want to spend any more time trying to save it. I just want it removed so I can list it on ebay. Will cutting away those brackets do the trick?
  2. M

    Evinrude 40 hp trim removal

    Lower pin.
  3. M

    Evinrude 40 hp trim removal

    I've tried everything in my arsenal but can't get the lower pin to move. 1999 johnson 40 hp. I just want the unit out of there so if I have to sacrifice the side brackets that's fine by me. Question is the corrosion that makes these stuck in the area where the pin passes through the mounting...
  4. M

    1996 evinrude 40 tiller carb roller

    Yes carb roller. Maybe its a commercial motor which i found on Google stating to use a pn 397499. I ordered one off ebay. Hopefully it fits
  5. M

    1996 evinrude 40 tiller carb roller

    New to me e40reds Ordered pn 0432639 from boats.net according to the parts picture. Length is fine but inside hole way too small to go over carb shaft. I found on Google part number 0330056 which looks like a bigger hole. Not sure why the one it calls for wont work. Anyone know if the 330056 is...
  6. M

    Convert evinrude 40 to tiller

    1996 evinrude 40 model e40reds I found the mounting bracket for the steering does anyone know all the parts needed to do the conversion? Anyone know if a handle from say a 6 or 9.9 would work in the bracket after installing the appropriate cable? Thanks
  7. M

    Skeg guard for 2003 yamaha 25 hp 4 stroke

    Anyone know if there exists a skeg guard for this motor? I have Google searched but coming up empty. Maybe someone knows of one that fits it but not necessarily advertised as doing so? Thank you You can see the damage in this picture
  8. M

    Yamaha 40 hp 3 cylinder wont accelerate

    Ok. Aftermarket cdi boxes are through the roof $$$ close to 1k. Oem discontinued.. Used is risky
  9. M

    Yamaha 40 hp 3 cylinder wont accelerate

    Agreed but is it unusual that the pointer is going so far past that higher mark?
  10. M

    Yamaha 40 hp 3 cylinder wont accelerate

    Take a look at the pointer on my cdi box vs throttle position. I can't find any info on what mark it is supposed to point to when.
  11. M

    Yamaha 40 hp 3 cylinder wont accelerate

    Ok
  12. M

    Yamaha 40 hp 3 cylinder wont accelerate

    Hi. I sold a 1989 yamaha 40 hp 3 cylinder tiller oil injected manual start to a friend. He took it out and it falls on its face when trying to accelerate. Compression is strong at 130 psi in all 3 cylinders. Spark is good on all 3. I had him squeeze the primer ball when it happens and he said he...
  13. M

    1996 ev 25 hp 2 stroke not peeing

    Here is the result of using a new oem pump. Works mint. Thanks to everyone that pisted for all the info.
  14. M

    1996 ev 25 hp 2 stroke not peeing

    Good to know. I'll check closely
  15. M

    1996 ev 25 hp 2 stroke not peeing

    Nevermind. Upon closer examination grommet is good to go. Nice tight fit to the water tube. Hoping it was just a junk pump. If this doesn't get the water flowing out the telltale i am not sure what else to do. Lower unit housing under the water pump is mint with zero corrosion or pitting so...
  16. M

    1996 ev 25 hp 2 stroke not peeing

    put my inspection camera up inside the exhaust tube and the grommet doesn't look too good. It's a short shaft motor so it's not too far of a reach to get up in there but i am sure it will prove difficult to do. Has anyone accomplished replacing the upper water tube grommet without pulling the...
  17. M

    1996 ev 25 hp 2 stroke not peeing

    This kit seemed especially cheap. The housing was 3d printed. Anyway I ordered an oem kit and will inspect the upper copper tube grommet when I am in there. Was run on muffs as I have done with countless other motors without issue
  18. M

    1996 ev 25 hp 2 stroke not peeing

    Picked up a nice motor 1996 evinrude short shaft model number e25teeda. I noticed it didn't pee right away. Wouldn't see a stream until 20 seconds or so after starting. I've run a bunch of these and always had them pee right away. I dropped the lower unit down and inspected the pump. The...
  19. M

    Evinrude 25 hp lower unit front stud

    The bolt turned into a stud worked great thanks guys. Much appreciated
  20. M

    Evinrude 25 hp lower unit front stud

    Genius. Thank you
Top