Search results

  1. 5

    9.9 chrysler year?

    Could someone say what year model #92 BE is? This number was given me by someone, my refs don't show it as a number, closest I can get is 92B1, or 92B2
  2. 5

    Gale 5D17B impeller

    Is the 1960 5hp Gale impeller the same as Johnson and Evinrude for that year?
  3. 5

    shift rod reassembly 4 hp '82? Johnson

    Could someone explain the proper sequence for reassembling the shift rod to the gearbox on a 4 hp model #J4brcnr? The shift rod bottom end finishes in a half cylinder shape how does that exert an upward force to shift [neutral-forward only] or stay in place? I now have the tower...
  4. 5

    1990 evinrude 2.3 hp water jacket cleanout

    Anyone have any tips for removing the white aluminum oxide build-up from inside the water jacket. It has very little flow from the tell tale on the cylinder The telltale nipple [brass?] is heavily corroded. Any way to clean it without cylinder head and cylinder disassembly?
  5. 5

    '90s 2.3 hp evinrude pumping?

    Should a 2.3 hp OMC be putting out cooling water, at low to very low speed? The water discharge slows and stops at slow rpm, normal? It appears to have a good flow at higher rpm in a barrel. Haven't had it on the boat yet.
  6. 5

    1990? evinrude 2.3 hp parts?

    Just got a 1990? evinrude 2.3 hp model HE2RESS, it has compression 110 lbs, fuel to cylinder, spark outside cylinder. Spark plug held against plug hole will fire fuel mix in cylinder, but it won't start. Seems like the coil to me. The sites I use to check part numbers and order from will...
  7. 5

    viking 6 hp year?

    Tried using the Chrysler chart after dropping the viking "4", no luck. Model number 64021
  8. 5

    2 hp evinrude year?

    Have checked a couple of sites, can't nail down the year model HE2RESS Thanks for any help, Phil
  9. 5

    '69 4 hp Johnson ignition wires

    Have tried several different routes for ignition wires on '69 4 hp Johnson 4W69B, under fuel pump, around outside fuel pump, between fuel pump hoses. None seems to give complete freedom of movement, especially on the low speed/ stop end. Perhaps the wires are cut too short?
  10. 5

    140 L/U to '95 150/175?

    Any chance an 80s or early 90s 140 L/U , would fit a '95 150/175 Johnson Sorry don't have the model numbers yet.
  11. 5

    QD 15 gasket #

    Have a manual on the way, but need a number for QD15 Exhaust cover gasket or gaskets. It appears to need 2 as the cover is in 2 pieces with cooling water circulation into each. Or should I just cut one out of my 1/32" paper gasket material, and use RTV hi temp gasket seal? I have some Permatex...
  12. 5

    '54 Johnson 10 hp head gasket

    Could someone help out with a part number, the parts manual has not arrived yet. Thanks
  13. 5

    johnson 10 hp QD 15 prop.

    Just got a QD 15 the other day, the prop. seemed loose and had a large washer under the prop. nut, a brass cotter pin was used on the prop. nut. Under the prop. was a piece of ardox nail, the prop nut wouldn't bring the prop tight and still allow the cotter pin to go in. I understand the std...
  14. 5

    '57 evinrude 5514 water pump

    Does anyone have a part number for the rubber nipple on top of the water pump housing where the copper tubing slides in? Should I use gasket sealer on the water pump housing or lower unit to tower connection? Thanks
  15. 5

    elto 8hp year?

    Hi, New to the forum, watching for a while, great stuff! I'm looking at an 8 hp elto looks something like a late 40s early 50s johnson/evinrude. Is there somewhere to look for a site with model or serial numbers indicating its age? Are they any good? Weak points strong points? Its an odd mauve...
Top