Search results

  1. B

    1987 wellcraft 18 off shore fisherman floor issue

    Bought this boat almost a year ago nice boat the only issue is the floor is soft, what can be a quick repair for this, i was thinking on use mat on the floor and use some fiberglass to make it hard again.
  2. B

    1987 evinrude/jonhson lower unit service

    Can anyone help me how i will removed and service the lower unit on my evinrude, i been looking online but cant find anything.
  3. B

    1987 evinrude johnson 150 v6 just replace the base gasket

    Hi i just replace the base gasket with the oem gasket put everything together enhine start and run very nice better than before, my question is with the engine off throttle in neutral the propeller spin freely, with engine off when i shift forward the propeller doesn't spin, when i shift reverse...
  4. B

    1987 johnson 150 stator issues

    Hi guys thanks for the help, i got this biat did a tune up on engine new batteries, new battery cables, when the engine running in water the voltmeter never pass 12v, sometimes is 11v, I test the statoras the manual said and is checking ok, i replaced the voktage regulator because i tested...
  5. B

    1987 johnson 150 base gasket

    1987 evinrude johnson 150hp im getting ready to replace the base gasket, do i need to disconect the shift rod?.
  6. B

    new boat installing a tachometer, temp gauge, battery gauge

    hi guys bought a 18 center console wellcraft with a 150 evinrude 1987, bought new gauges the old ones weren't connected and not wiring, I need to connect the tachometer, the temp and battery gauge any help with that thanks.
  7. B

    new boat installing a tachometer, temp gauge, battery gaude

    hello and thanks for the help as always I just bought a 18 offshore wellcraft year is 1987, with a evinrude 150, this boat was parked for a long time Im replacing the temp gauge, I bought new set of gauges but was not wiring before on the old gauges, everything was a mess, any diagram or help...
  8. B

    engine knock oil pressure down 1987 seareya 5.7

    Hello guys 1987 searay 5.7 engine, alpha one gen 1, engine was rebuild recently by a shop, put boat in the water and after engine warms up oil pressure goes down to almost cero, and heavy engine knock coming up from engine, I notice oil on the bilge check level of oil and is ok. Any ideas.
  9. B

    new engine oil pressure going down

    hello guys 1987 mercruiser 350, was rebuild, when start the engine oil pressure is about 40, when engine warm up pressure go down to 20 and bellow, If I accelerate the engine pressure goes to 50 -60, engine oil weigh is 25w40, new oil filter, any advice thanks.
  10. B

    lost power new engine help

    hello guys 1987 searay 350 5.7, engine was rebuilt,new edelbrock manifold, new edelbrock carburetor, finally put the boat in the water after engine and interior been fixed, going forward 1500 RPM-1800 Rpm but run smooth, temp, oil pressure, reads ok, the for the first time slowly I accelerated...
  11. B

    engine kill switch?

    Hello guys 1987 searay 5.7 I/O, I want to install a kill switch for security purposes how can I do that, again thanks for the help.
  12. B

    gelcoat and fiberglass question?

    Hi guys I made a new engine cover and I used math and cloth, I want to painted with gelcoat the box dry and looks very good but is not smooth my question is I need to sand and leave it smooth before painting?. thanks.
  13. B

    starting issues

    hi guys 1987 searay 5.7 I/O, has dual batteries with a switch, new starter, new alternator, new batteries, the boat only start when the switch is selected on both batteries or battery 2, if I selected battery one nothing happen. The switch been installed according to instructions. battery one to...
  14. B

    shift in to reverse issue

    hello guys, 1987 alpha one gen 1 replaced the shifter control at the side panel of the boat and the boat shift perfect to forward but when in going in to reverse has a rrrrr then shift, before this was not happening thanks for advice.
  15. B

    battery isolator, good idea?

    hello guys need some advice I have a 350 5.7 searay, with dual batteries and someone told me why I don't have a battery isolator?, is that a good advice, what is the benefit of that, need some feedback thanks.
  16. B

    white smoke rebuild engine.

    hello guys 1987 searay 350 5.7, just have the engine rebuild and upgrade to a edelbrock marine carburetor, edlbrock marine intake, new plugs, wires, cap, rotor, put in the water today, and noticed white smoke coming out of exhaust, even after I flush the engine with the muff notice a lot of...
  17. B

    help need to build a engine cover

    hello guys 1987 seara 230 5.7 I need to build a engine cover for it any ideas?, thanks.
  18. B

    intake manifold question

    hello guys 1987 mercruiser 5.7 im looking for a intake manifold and I was looking a edelbrock 2506, or 2504, what is the difference between this two intakes? or both will fit the engine, thanks.
  19. B

    ngk or ac spark plugs?

    hi guys 1987 350 engine, 4 barrel carb what spark plugs should I install on the engine some manuals calls for mr43t, or ngk 4323?, any recommendation.
  20. B

    engine alignment question

    Hello guys getting ready to install the repower engine on my 23 searay 1987 350, I replaced the engine mounts the old ones were shot, my question is when I drop the engine and Im ready to turn the nut of the mount according to alignment procedures I have to turn one at a time or both on same...
Top