Search results

  1. G

    How to build a super heavy duty 6600lb trailer mover

    No steering ideas at the moment, the wheels are wide apart so it makes steering a little bit difficult as both wheels are drive wheels I havent painted it just yet i have used it around 8 times i also changed the 2 relays to a large winch relay
  2. G

    How to build a super heavy duty 6600lb trailer mover

    Hey Guys here's a video i made converting a direct drive mini mover 2 trailer mover to dual offroad wheels, i used 10mm and 16mm plate steel i welded it together with 2.4mm arc welding rods Its pushing a V19 fibreglass center console in the video around 4400lb up a 5 degree incline on light dry...
  3. G

    Free Boat, This thing is a badboy!

    I faired one side section quiet afew months back and only just sanded it back for the hull to be painted Lastly a pic of how the boat turned out with a small homemade windscreen
  4. G

    Free Boat, This thing is a badboy!

    Starting to work on the paint job over the past few days i have been applying paint stripper to remove the old peeling and cracking paint on the top deck I used the pressure washer today to blast off most of it very hard going as the paint is very thick actually looks like house paint Applied...
  5. G

    1993 Celebrity Status 208 Stringer and Deck Replacement

    Stringers have to be the most difficult part of a boat repair so take your time If u can gut the whole hull now it will give you assurance in years to come it was all rebuilt, what you don't want to happen is to do a part repair one stringer than put a floor down to find out in 2 years the...
  6. G

    2021 Splash of the Year Voting

    Good Luck Guys
  7. G

    2021 Splash of the Year Nominations

    Thanks for the nomination guys :-)
  8. G

    Free Boat, This thing is a badboy!

    Hey Guys, a couple of videos offshore of the old girl working my cousin said it was 6ft swell
  9. G

    Free Boat, This thing is a badboy!

    Thanks Kc
  10. G

    Free Boat, This thing is a badboy!

    Took her out in open water yesterday riding over the swell at around 20knots she rode beautiful the bow done all the work, she was very stable and predictable in over taking swell in a following sea, she drove very stable going across the swell at an angle, she even done well over taking a...
  11. G

    Free Boat, This thing is a badboy!

    Welded together my seat base and made a windscreen
  12. G

    Transom rot

    I done my 19ft transom in less than 50 hours, what took the most time was the epoxy resin "curing" which is not calculated in the rebuild time, each epoxy laminate takes 48 hours to cure for sanding You can cut the outside transom skin 3-4 inches in around the outside than chip out all the...
  13. G

    Free Boat, This thing is a badboy!

    Took her out today she topped out at 60.05kph or 37.2mph
  14. G

    Free Boat, This thing is a badboy!

    Are you guys taking the **** or what?.. who would raise it to the bottom holes to start off... you'll fry the engine!
  15. G

    Free Boat, This thing is a badboy!

    There is nothing wrong with howits set up
  16. G

    Free Boat, This thing is a badboy!

    Racer... just look back thru my pictures
  17. G

    Free Boat, This thing is a badboy!

    In your opinion what is wrong with it?
  18. G

    Free Boat, This thing is a badboy!

    No its just the way i designed my transom i wanted a higher sides than 20" as u can see but i needed the 20" cut out to fit the engine and make sure i had turning clearance, can u imagine how much water would have came over the back had i gone the 20" height right across the back? Ahuh lucky i...
  19. G

    Free Boat, This thing is a badboy!

    Hey Guys i took her out a couple of days ago but had engine problems my alternator wasnt working, i will test the boat again next week Heres a video
  20. G

    Free Boat, This thing is a badboy!

    Hey guys just done some light power draw, i have 2 cabin lights, 3 navigation lights all 5 lights will be using .95amps My trailer is now registered and im just waiting on a steering arm before i take it for its maiden run
Top