Search results

  1. N

    Motorguide Pro analog to digital

    I can't find anywhere the conversion kit for my one year old MG 70 lb trolling motor can someone help me?
  2. N

    Motorguide Pro Series 3 speeds down.

    I bought a 70 lb mg tm about a year and a half ago new from BPS and I don't have the original receipt but I'm pretty sure I sent in the warranty info and this week I lost three speeds on my motor. What can I do to get the unit fixed and is it something I can fix on own?
  3. N

    Trolling Motor Help

    I have a motorguide pro series 70 lb foot controlled 24v trolling motor and it is just over a year old and the 1 2 and 4 speed have ceased to function. I replaced the rotary switch and it didn't change anything. Is the motor going out on me? Any ideas?
  4. N

    Bass Boat tubing that covers lines

    I'm looking for the tubing to cover the lines and hoses that are exposed from the hull to the outboard can someone push me in the direction?
  5. N

    Rate the used wakeboard boats

    Hey guys I'm looking at some wake/ski boats with inboards but I'm not spending more than low twenties on a used boat. Can you guys rate them and give me some suggestions.
  6. N

    150 efi shaft length?

    Hey I have a 150 on a nitro bassboat and have been considering a 200 or 225 upgrade. Do I need a 25 or 20 inch shaft? Thanks for your help.
  7. N

    97 seadoo gs

    I have a hard time taking off with a passenger if I go full throttle the motor cavitates is this normal? I have heard of wear rings should I replace mine? How difficult is it to replace. Once taken off the machine hauls.
  8. N

    bilge question on 97 nitro

    For my bilge pump to run I have to have the manual switch on at the console and it never shuts off. Should this boat have an automatic bilge? I'm going to replace the pump. Any info would be great.
  9. N

    Max motor on 18 ft riviera cruiser

    I have a 35 hp motor on it now and it has no power how big of a motor can I put on it safely?
  10. N

    Location of Bilge Pump on Nitro Bassboat

    My Nitro bilge pump has been running sluggish lately and it is a 97 I'm going to replace it but I'm not sure exactly where it is located. My boat has a massive 30+ gallon tank and three battery trays so I don't want to start digging without a good direction.
  11. N

    Safety Equip. for 19 foot bassboat(Ohio)

    Hey guys, I read the Ohio laws but I don't know what qualifies. I have a whistle, distress flag, new handheld flares, type 1 life jackets and a throwable. I gave away my anchor when my dad lost his so I'll have to replace that. Do I have to get a air-horn? Thanks guys. This boat is only used on...
  12. N

    150 efi compression question

    My merc has been running great and have had no issues since early summer when I had it repaired finally. I had a complete tuneup and they did a compression test and marked 100 on every cylinder is that a percentage or reading? He said the compression was fine when he went through it. Should I be...
  13. N

    Bass Boat tubing

    I have a Nitro with a 150 Merc outboard and I'd like to pull tubers can I use the transom rings on the back of the boat to tube and ski? Any pro's or con's. Will the rings pull out?
  14. N

    150 efi merc fuel issue

    I just got my boat back from the mechanic where I had an issue with one of my temp sensors so dumping fuel into cylinders. Boat ran great today really powered out of the hole and after sitting for a while I went to take off and she died. Bulb was soft as heck and took a lot to pump hard. After...
  15. N

    150 Efi No Power Under Load

    I have a 97 Efi 150 motor idles fairly normal but when you tromp it it runs up to 2000 RPM and no further forget about getting on plane. After this occurs the bulb is soft. Is it the check valve? I just had this boat serviced and tuned up and it ran great one time out now blah. Made for a crappy...
  16. N

    Jackplate ????

    Hey pros would my boat see more performance from a jackplate? What are the pro's and con's? If I get one how can I make sure not to lean out the motor? Do you get one that is stationary and still trim up? I'm new to these but all of the new bass boats seem to have them. Who is a provider for a...
  17. N

    Boat Painters in Ohio

    Hey guys I'm looking for a company that will prep and paint my bass boat if you know of any can you direct me?
  18. N

    installing prop seal ring

    I just received the seal ring for my 97 efi 150 hp how do I go about installing it? Thanks guys.
  19. N

    prop suggestion

    I have a 2001 16 ft alumacraft fishing boat that has a livewell and an interior with a tiller steer 25 hp johnson motor which is a 2000 model. The motor runs great but won't plane out with this boat. They weren't a matched set so I'm curious as to what prop I should put on it. The boat is pretty...
  20. N

    gelcoat refinish?

    My 97 Nitro has a burgundy bottom with some gouges and scratches on the bottom. Should I use the gelcoat repair kit I have and try to match color or fill in major chunks then gelcoat repair over? I also want to sand down and buff bottom and top what products and equipment are needed?
Top