Search results

I need some help with understanding leaf springs. I changed the leaf springs on my boat trailer because the rear of my trailer was very low. At first I thought it was the ball up front but when I made adjustments to that the ball the rear of the trailer stayed the same. So I decided to change...

Something is wrong with my steering, as I am steering boat I am compensating for veering every second....the boat will not run straight...the veering is driving me nuts...When I'm out on my friends boats, he can take his hands off his steering wheel and his boat will ride straight for about 15...

When I set up my butt seat, my poll is bobbing all over the place....this is a used boat I just bought...I thought is was the bushings in the mounting plate, but I ordered new bushings and I get the same results...Both the mount and pedestal are 3/4 (Which I understand to be standard) my pole is...

I need some help with parts... I noticed I had some water in my lower unit... According to the parts diagram, there are only 2 seals and 1 o'ring that need to be replaced... on the bearing carrier...(If i'm looking at the diagram correctly) # 31 and 49 I circled in red... Am I correct in saying...

I'll have a problem with I believe is my boat planing too high. The boat nearly sits almost straight up in the water to where I have water coming in over the back Edge. The boat is a 20 foot Nitro bass boat with a 120 on the rear so I know I'm not overpowered I do have the motor raised up to the...

OK, I had an issue with the motor bogging down,,,after rebuilding the carb's, changing the fuel pump (to the new style) and fuel lines..I took the boat out today...I tried starting the motor ..it would not start...I sprayed a little starting fluid into each carb and the motor would run and idle...

I was wondering if someone new the correct spark plug size and gap for an 1986 Evinrude 120hp Thanks Mav

Wanted to see if someone can help me identify my MotorGuide trolling motor. I need to get some parts but cannot find the serial number anywhere however I did find the following numbers 2AF127-01M (Found on the inside head) FEY59484 ( found on a white sticker under and in the inside head of the...

I have a 1986 Evinrude 120hp...I want to disconnect the the VRO pump...But when I went to disconnect the pump, I saw that the fuel pump was directly in the rear of the VRO pump...I have 2 questions....Dose any know if this is a electronic fuel pump, if so by disconnecting the VRO lead would...

I have a 1989 Evinrude 140hp...I have no spark at the present...At the present I don't have the motor connected to a set of control I just picked up the motor the other day...I guess my question is, does anyone know if there is a kill switch on the motor that i would have to short out to see if...

I ordered some shift&throttle cables from ebay..What I missed was they did not come with either ends....I have been pulling my hair out trying to find ends for the control box side as well as the engine side...I have had no luck, I can't even find the names of the ends anywhere online... Any...

I have a 1989 Evinrude 140 with no spark....I have 3 sets of wires that i have no idea were they go. They are coming from the junction box...One set of wires have 5 wires and the other 2 sets have 2 wires...I believe one set of wires are for the oil pump....I guess the question I'm trying to ask...

I have a 1989 OMC control box that has the standard wiring diagram...I bought a wiring harness (for the control side) from ebay, but in stead of having the standard red female plug (like on the motor side) it has a black plug which has different colors wires. (I'm going to try to post some...

I have a 1989 Ford 150 horsepower. I finally got it started but it was shooting water from under the block. if you were to stand in back of the motor on the left side on the block water was coming out like a waterfall underneath . I was told it was the cooling jacket gasket. but everything I...

I have a 1989 Force 150 5 cliinder, I'm having an issue with it starting...it has great compression, getting fuel, and great spark, but it didn't seem like it wanted wanted to start or even sounds like it wants to start...Today I put some fuel in the top spark plug hole and it sounded like it...

1989 Ford F 150 horsepower good compression good spark getting fuel will not start don't want to even sound like it wants to start want to know if there's a safety switch on the motor somewhere because I'm trying to starr the motor without the controls double checked Spark Fuel and compression...

Wanted to ask a quick question...I have a Force 150hp starter, I took the starter off the motor to check the starter because the motor was spinning very slowly...After checking the batteries,the wiring and connections (all was good) the motor still spent slowly..So I tested the starter with by...

I have a 1990 Force 150hp and I can't find the manual release screw for the tilt&trim...Dose anyone know where the release screw is, I have the book, but I can't find it anywhere in the book. Thank's Mav

I have a 1990 Force 150hp....the boat that I have came with a Suzuki 150hp but the boat also had OMC Controls...I was wondering if I could use the OMC Controls with the Force motor.. Thanks Mav

I'm re-powering my boat and I'm going from a Evinrude to a Force..The Evinrude mounting bracket holes are wider then the Force mounting bracket. Is there a bracket I can bolt to the existing holes in my transom, that will allow me to bolt the Force motor with drilling more holes in the transom...