Search results

  1. Scott Danforth

    Caught a break

    post the numbers, most likely a wix filter with a rebrand
  2. Scott Danforth

    Killing time

    neighbors daughter in 4H had an outdoor pen full of rabbits. one night there was a slight commotion. a Florida panther reached up thru the hardware cloth at the bottom of the cage and strained the rabbits thru the claws and cloth. only thing left a minute later was some red tinged fur in the...
  3. Scott Danforth

    2021 Tohatsu 20hp EFI starter kit

    thanks, will pass it along.
  4. Scott Danforth

    2021 Tohatsu 20hp EFI starter kit

    Posting here for those more knowledgeable on Tohatsu's like @pvanv coworker just picked up a 16' aluma craft with a Tohatsu 20hp EFI motor. While the motor starts easy, he has 2 fused discs in his neck and would like to upgrade to electric start since he also boats on the ICW, he will need to...
  5. Scott Danforth

    Windshield Support Rods...

    make a longer rod, or buy a longer rod, or grab a bit of composite window shim and make a plate. however you may want to see if the two consoles are tilting inward, indicating the floor is sagging in the middle. put a straight-edge across the floor and verify.
  6. Scott Danforth

    Killing time

    all cornered animals bite. its the only thing left in the flight or fight response
  7. Scott Danforth

    projects other than boats

    My bud Andreys toy
  8. Scott Danforth

    1991 OMC Cobra 2.3L - can't reach max rpm

    before you worry about timing, you must file the points, rough gap the points, and set dwell with a dwell meter.
  9. Scott Danforth

    thompson 240 transom rebuild

    I recommend working on the inside. Being 1988, and a Thompson (during the 80's transition period), I am pretty sure that once you get to the stringers, you will also be replacing all the stringers,
  10. Scott Danforth

    1991 OMC Cobra 2.3L - can't reach max rpm

    will second both above...... compression and ignition what are the compression numbers? did you service the points and set the dwell on your ignition? did you then set timing?
  11. Scott Danforth

    Oil capacity and accuracy of dipstick questions, 2017 VP V6-200-J

    oil level is about 4" below the pan rail. use that as a guide on your dipstick
  12. Scott Danforth

    Is it capable of planing?

    that boat should have no less than 30 hp on it. (75% of rated) at 7500 feet, your 25hp motor is putting out about 18-19hp as jimmbo stated, drop the prop pitch to get the WOT RPM to the upper end of the window move your fuel tank and batteries forward to balance the load Im going with a...
  13. Scott Danforth

    projects other than boats

    Light reading on a V8 Healy https://www.jalopyjournal.com/forum/threads/extreme-v8-healey-build-thread.1350596/page-2
  14. Scott Danforth

    projects other than boats

    Joe, you can always get goats.
  15. Scott Danforth

    Artificial Intelligence

    One of the facetube groups I am on for the 1957-1955 GM trucks recently had a poster use AI on removing the tailgate hinges. Those trucks use two carriage bolts to hold the hinges. Accessible from inside the stake pocket. Yet the two AI answers that were posted both were made up with 20% of...
  16. Scott Danforth

    Gauges don't work

    The gauges are all daisy chained together on both power and ground
  17. Scott Danforth

    projects other than boats

    Will sell you a 22" personal pace
  18. Scott Danforth

    projects other than boats

    A tilton 7-1/4" triple clutch and flywheel showed up on Facetube marketplace...pick it up before noon
  19. Scott Danforth

    Mercruiser 454 I Need Help Identifying This Engine

    There are about a dozen great machine shops in New Jersey LRB is one D&F, Olsen Engines, or Chucks Automotive come to mind
  20. Scott Danforth

    I/O (Sterndrive) Conversion to Outboards

    Bet the anticipation is building
Top