Search results

  1. S

    Can anyone help me with removing a flywheel?

    Purchased about 5 outboards and the frustrated seller complained it had a locked flywheel. All came off in minutes.
  2. S

    extremely high idle suddenly

    How long was it at 4000 RPM's? Not long I hope....in neutral?
  3. S

    Can anyone help me with removing a flywheel?

    Steering wheel puller, impact or hand wrench very tight. One big smack gets mine Everytime. Big hammer. Show picture of your puller.
  4. S

    1978 Evinrude 208CR02 parts cross reference — can I use 25803C parts?

    Does it have the through exhaust propeller? Should be able to use anything in the year as long as the gearcase is the same. Other gearcase has a cone on the back of the prop. Carb exchange is all you need to up the power.
  5. S

    Evinrude 40 hp trim removal

    Not really sure of how you would "Cut it away" but possibly. I would think doing it the way I describe wouldn't take and longer...at least actual cutting time. Done plenty myself that were completely salted up... The pin will also be stuck in the t&t too so I can't see listing it without that...
  6. S

    Evinrude 40 hp trim removal

    Trim pin or the t&t unit lower pin? Either way, heat and lots of it....then melt wax in it....do it many times until they come out with a drift pin and hammer.
  7. S

    1995 60hp Power Tilt Trim Conversion

    After market is probably your only choice. Cmc....look them up.
  8. S

    Check Timing Joe Reeves method question. 200hp Johnson

    650 on the lake under load or 650 in the barn?
  9. S

    1996 johnson 200 running Rough.

    The white washer you used....under the seat? If so, your needle is not allowing enough fuel flow. You were told this, looked at the breakdown, yet you still did it? Just making sure this is what you did.
  10. S

    1987 johnson 50hp vro keeps blowing 4 amp fuse

    The right fuse and your golden.
  11. S

    tilt and trim Johnson 50HP 2000

    And there you go...we will never know. Lol....
  12. S

    tilt and trim Johnson 50HP 2000

    Pump side? It should all work through one hole, so I don't understand that. Also, hook it all up then do it period. Without weight, your not "purging" anything. Does the motor and pump sound like it's cavitation when you have failure or does it quit running? Last but not least, with the motor...
  13. S

    tilt and trim Johnson 50HP 2000

    Explain in detail your purging process.
  14. S

    tilt and trim Johnson 50HP 2000

    Not sure if you mentioned to send a link but nothing works when I tap it.
  15. S

    1995 Johnson SPL extra telltale question

    Getting a pic of the actual hole would settle it for sure. If it looks like a hole a manufacturing company would make...it probable is. Test to see if the overheat alarm system is working...did the motor get hot? All clues.
  16. S

    2005 PLSOR cuts after starting

    One plug, one jumper wire....so easy.
  17. S

    2005 PLSOR cuts after starting

    1st thing you do with an electrical issue on a remote start outboard.
  18. S

    2005 PLSOR cuts after starting

    I guess that's what you mean about bypass? I'm like AI....some wire somewhere.... corrosion.
  19. S

    2005 PLSOR cuts after starting

    Reading through the thread here...am I missing something? Have you unplugged the control box and jumped it at the motor? Kill circuit, wife overboard clip.
  20. S

    ‘83 7.5hp powerhead gasket

    How were the mating surfaces? Salt water motor?
Top