Search results

  1. C

    Etec 75 hp

    no expert on boat performance but 75hp ETEC known to be 10% underrated so you would have about 82-83hp to push your rig... not much difference big big savings of $5G fuel low oil consumption NO SMELLY OIL using xd100 great torque ... consumes .6L/hr trolling and the early ones actually...
  2. C

    Key won’t crank like it’s not in position

    glue ? :)
  3. C

    Etec 75 hp

    first thing to do is check in with the folks at the ETEC owners board and submit your question for ETEC experts to comment. Board has an excellent search engine https://www.etecownersgroup.com/latest your 2004 is 22 years old with very little use if the EMM is the original one that came...
  4. C

    1962 evinrude fatwin 18hp carb settings.

    fyi
  5. C

    1962 evinrude fatwin 18hp carb settings.

    no need for a "timing tool" see video a plain VOM works fine .. At START the cam follower on the carb should line up with the bar on the cam under the mag plate. "coil gap" is the same .... just run your finger nail up-down the face. if it snags going up or down adjust coil position
  6. C

    1962 evinrude fatwin 18hp carb settings.

    Never had an issue myself if the back screw is just release a bit to allow rotation adjustement & as a means of reducing excess torquing on the pivot screw. As per video a recheck of alignment when done confirms all OK .
  7. C

    Evinrude 50 4 stroke 1999 been setting, need to restart suggestions/ guidence

    some pumps... have ben known to be revived on ETEC engines by short reverse polarity kicks and feeding the pump some oil.. let it soak and retry inverse polarity kicks... then forward polarity some have even boiled the pump (in a plastic bag) but I never tried it myself. injectors can...
  8. C

    1962 evinrude fatwin 18hp carb settings.

    suggest you download the manual I provided a link to see post #6 it contains all the info you need. condensers may be ok but at least it needs a basic OHM test and capacitance ...with a capacitance equipped VOM ... refurbing an oldy involves parts which can add up to $100+ so figure...
  9. C

    1962 evinrude fatwin 18hp carb settings.

    fyi
  10. C

    Key won’t crank like it’s not in position

    On a 1970 115 hp Johnson / Evinrude, there’s no magnet or electronic trickery—the neutral switch is purely mechanical, but it can be deceptively subtle. What’s actually happening That 0382548 neutral switch is a spring-loaded plunger switch that is: Mounted right beside the shift linkage or...
  11. C

    Key won’t crank like it’s not in position

    If nothing is physically pressing on the switch plunger, then it’s not a direct push-button style actuation. There are two common ways that 0382548-type neutral switches get triggered: 1) Cam / ramp built into the shift mechanism (most common) Even if you don’t see a rod pushing it, the switch...
  12. C

    1962 evinrude fatwin 18hp carb settings.

    officially the OMC brand FW puller is the best $$$$ but a basic /cheap harmonic puller work fine... it has for me anyway .. notice the inverted nylon nuts I installed.. this keeps the bolts in the puller and more important it stops you from driving the bolts in to far into the FW which could...
  13. C

    1962 evinrude fatwin 18hp carb settings.

    Kits are only good if the internal passages are 100% clean and should be your starting point Inspecting electrical is not an option to skip !
  14. C

    Key won’t crank like it’s not in position

    motors have different neutral interrupt switches ... one is sometimes up front on the throttle and when put in START it fires up the solenoid which in turn fires up the starter etc.. For safety reason that simple function is frequently interupted by a safety device to PREVENT...
  15. C

    1962 evinrude fatwin 18hp carb settings.

    typical condition of coils mentionnned by racerone... your MUST pull the fly wheel and service the electrical. lots of utubes and folks to help out as your bring it back to life ! "The foot grease had no oil in it" no grease here refill with oil !!!
  16. C

    1962 evinrude fatwin 18hp carb settings.

    Download this oldies manual for johnson servicing the johnson FD16 is likely evry similar to your Evinrude 18hp book contains all the infor you need to service these older models ....see carb section etc.. a good book to cover the OB basics even if your Evinrude is not in there free...
  17. C

    1939 Evinrude gas tank

    chat says no
  18. C

    1978 Johnson 140hp running rough. Need advice

    kind of curious what can go wrong with a carb other than expendable parts the rest is just holes to clean out and mecanical links.
  19. C

    Mounting bracket for j200

    somebody Knows. me I would seal existing holes with silicone or epoxy and drill new holes where they are needed.
  20. C

    2003 Johnson 150 throttle

    https://www.bing.com/videos/riverview/relatedvideo?q=utube++oiling+shifter+cables&&mid=44EAD4B4E12E9FDF785844EAD4B4E12E9FDF7858&churl=https%3a%2f%2fwww.youtube.com%2fchannel%2fUCEX1WAuC8uQWlYIIIQJjhtw&FORM=VAMGZC
Top