Search results

  1. C

    1996 johnson 200 running Rough.

    I found the problem with rough I have plenty of for fire, I pulled each wire off one at a time running, stuck a screw driver in it and held close to ground . Jump 1 inch and sounds like LIGHTENING!!!!! the cause of the rough running was water in the fuel, I had water in it last year, so i...
  2. C

    1996 johnson 200 running Rough.

    The oil / fuel pump is deleted.
  3. C

    1996 johnson 200 running Rough.

    I did it, took it out to the lake and ran it hard, running great. I set the float to make the difference, if anyone ask you, be sure to tell it works just fine.
  4. C

    1996 johnson 200 running Rough.

    This motor has the oil deleted, it running pre mixed fuel.
  5. C

    1996 johnson 200. Carbs question

    I used them, set the floats, the float has plenty of travel up and down,
  6. C

    1996 johnson 200 running Rough.

    The hoes is an1/8 from the front lower of the crankcase. The floats were set, the carburetor comes off without disturbing the linkage , its all connected on the throttle plate.the throttle, Ill check the spark gap, And make sure coils are firing, the one thing I may have done is i used the...
  7. C

    1996 johnson 200 running Rough.

    I have a 1/8 vacuum line coming fron the crank case, I plugged it, I dont know where it should go. Could the electric primer be letting fuel through it? The did have the purple white wire disconnected, i added a plug and reconnected it, it doest can the rough running either connected or...
  8. C

    1996 johnson 200 running Rough.

    Motor new to me, it running rough, I have rebuild carbs, clean the holes in the throttle plate, stars and runs easy. I have sprayed carb cleaner on the carbs, throttle plate and the intake manifold. Crank case seal, check for loss fuel lines, I cant find an air leak, I pulled the plugs and...
  9. C

    1996 johnson 200. Carbs question

    Im rebuilding a set of carbs, the old needle set doesn't have the white seal, but the kit includes it. I just readjusted the float. Does it matter as long as the is set?
  10. C

    Mounting bracket for j200

    The top bolts are 3/8 to close that 3/16 each side. I built a rack to hold the old motor today, I believe the bolts with have enough slack, I can split the difference between the new bottom holes and the top. Thanks guys, I believe i was over thinking it. I just didn't want to drill and plug...
  11. C

    Mounting bracket for j200

    Thanks. Ill file them larger.
  12. C

    Mounting bracket for j200

    What do you think about milling the 2 top holes ovel? Would it weaking the brackets?
  13. C

    Mounting bracket for j200

  14. C

    Mounting bracket for j200

  15. C

    Mounting bracket for j200

    Im changing motor for a 90 160 to a 96 200. I had to add a 5" life kit for the 25 inch shaft, the pictures im post sh I w the measurements. Its off by 3/8 , will the bolts have enough play to compensate for it?
  16. C

    Motor

  17. C

    Motor

  18. C

    Motor

    After removing the motor, I have started working on a 5" lift bracks for my new to me motor . I used the 2 bottom holes and plugged the to. The new brack dose no ise the top holes. My question the bolts holes in the new riser plate are of in with.
  19. C

    Motor support racks

    until i sell them or part them out You right, I have to much to loss if it fell overail
  20. C

    Prop Rotation

    I spoke with the previous owner about getting my titles.He says one of them is counter rotation. Thanks, I will do more research, im installing one next week. The other options as mentioned before is to pull the cover, pull the plug shift it in foward gear and see which was it turns. L...
Top