Search results

  1. Dukedog

    1986 mercury xr2 blackmax 150 no spark

    you really need an oem service manual (#976583) for your particular motor.. will have all your test information... not seloc/clymer or any other after market.. yes i've seen new parts be bad from tha get-go.. particularly 'lectric parts...
  2. Dukedog

    Hesitation at wot help

    chris has ya goin' in tha right dirrection.. its gonna be fuel delivery... oiler has nothin' ta do with it.... being a '02 its gonna be whats called an electronic motor (non switch box).. its possible tha ecm may have a glitch... jus gotta keep lookin' for it... gl.
  3. Dukedog

    2003 Mercury 200hp Saltwater edition 2 cycle, can the oiler be deleted?

    see post #14...................
  4. Dukedog

    2003 Mercury 200hp Saltwater edition 2 cycle, can the oiler be deleted?

    injection.... bleed is removing puddling/excess fuel... mostly at idle and/or lower rpm.
  5. Dukedog

    2003 Mercury 200hp Saltwater edition 2 cycle, can the oiler be deleted?

    boy! you cats are strange.............................. "fence post anyone?"
  6. Dukedog

    2003 Mercury 200hp Saltwater edition 2 cycle, can the oiler be deleted?

    tamatoes, tamotoes.... off course it gonna start with what evers in it.... tha ecu has absolutely nothin' ta do with tha oiler.. nothin'g else on tha motor except tha linkage (which is tha only thing that determines what ratio its gonna get) and pluse that keeps tha main tank full are tha only...
  7. Dukedog

    2003 Mercury 200hp Saltwater edition 2 cycle, can the oiler be deleted?

    racer may be wrong on this one.. "Operation of the Oil Injection System The oil injection system delivers oil mixture on engine demand, from 100 to 1 at idle to 50 to 1 at wide open throttle." tha big "gear on tha crank stripped/melted" both problems are usually caused by some type of overheat...
  8. Dukedog

    2003 Mercury 200hp Saltwater edition 2 cycle, can the oiler be deleted?

    yes, it can... like racer says, tha bleed stuff has absolutely nothin' ta do with tha oiler............ *justa note.. if you know tha history of tha motor and it has "never" been over heated and its (oiler) still workin' properly then no reason ta delete.. if ya don't know 'bout tha motor then...
  9. Dukedog

    Will a Merc '77 IL6 gearcase fit a '93 Merc V6

    it will bolt up by removing tha front stud but its not advisable ta run it ona V6... tha driveshaft is "about" an inch (give or take) to short.. closer ta 3/4 of inch.. won't last...... we use ta run 'em but we had a 16" clamp/trim/brackets with a cut and resplined driveshaft, low water pick...
  10. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    not a clue?.. what ever it is it should not have been there............... tha only thing on tha "outside" of tha tube will be tha plastic guide tube on top of tha pump... it usually gets melted without tha exhaust "can" in place......
  11. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    your pressures aren't gonna change till you address tha holes in tha adapter plate....................
  12. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    you are describing exactly tha way some act straight outta tha box from merc with tha way it cools.. we called it "consumer R&D".... yep... restricting tha discharge from tha poppet will slightlt increase tha pressure with most motors but not all.. it still depends on tha drain holes in tha...
  13. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    "Now on the one-piece plate the 2.4 dump hole were pretty close to the right size but I still modify them. The 2.5 plate dump holes were all over the place. I have seen some that were so big the motor could not get more than 5-lbs. water pressure at 9000 RPM. I weld up or tap and brass plug all...
  14. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    jus for info.. do you are anyone helping you have any experience with tha V6 merc??? as for your concern with pressure go here, follow his specs, and your concerns will go away... might as well pull tha powerhead and check this.... yours (adapter, coolin' system) is tha same as his BIG motors...
  15. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    ya need a spark tester or use your timin' lite ta test for fire on each clyinder off idle..................... or if ya like me i sometimes pull one plug completely out and start tha thing... do all six undividedly... you can wait till dark if ya have trouble seen' any spark from tha plugs.. but...
  16. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    look here for a build date stamp.. may not be very readable but its there on tha block somewhere... should be area "behind tha advance timin' arm", kinda behind tha bend in tha arm....
  17. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    chris, his motor has tha older WH's that have been changed which do not have anyway ta change idle except jetting.. his motor came with WMH's... its sounds 'lectric ta me... parts and/or wiring... if ya spray fluid in it and it does nothing but bog its not firing on all cylinders for whatever...
  18. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    thats a very nice piece for its age!.. . its probably tha easiest merc V6 ta work on and will live forever if taken care... even still has tha cle on it! if your boat is a lite weight it won't disappoint.. jus keep in mind that even though it comes from tha high performance side n all dolled up...
  19. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    "merc didn't build a '93 XR2"..... sorry!.. never thought i'd see something like that ona site like this...
  20. Dukedog

    Mercury V6 XR2 - Does this Stator looks bad?

    thats a painted light weight.. you must have tha high performance XR2.. mount for tha hi perf. lite weght cowl also... thats a completely different story.......... not many of those left, especially here in tha states............ got my attention now.. what boat is it on?.. pictures?
Top