Search results

  1. Franco_boater

    Impeller base gasket Alpha One Gen 2 question

    Hello my friends I hope you are doing well, 3 years ago ive replaced my impeller, now i want to check it, I ve found OEM gasket in my stock, its OEM Quicksilver but its different than Ive used in the past I think i have used newer one and now found older style. I have this already installed on a...
  2. Franco_boater

    Milky oil Mercruier 3.0 / how to pressure test engine ?

    You mean to pressure it? I was thinking about acetone test
  3. Franco_boater

    Milky oil Mercruier 3.0 / how to pressure test engine ?

    Ciao my friends, I know its quite common problem so I have decided to create this thread... When drainin the oil it was milky, like a brown coffee. Engine runs fine so I dont know why there is a water, how to pressure test the water passages to check if the head is OK?
  4. Franco_boater

    New ujoints grease doesn’t spread evenly

    Ciao my friends Last year we have replaced unjoints in my alpha 1 gen 2, It has outside clips, it was very tough job but we did it. It’s greaseable with zerks. Before the season it was new grease there, after half year and only 20 hours I wanted to regrease it. Connected grease gun to the zerk...
  5. Franco_boater

    When is the time to reseal your drive?

    Hello, when changing my upper gears and shift shaft bushing My friend who owns a boat and we are boating together was wondering when it’s good time to reseal your drive ? Because my shift shaft bushing was worn and allowed for water intrusion that caused me yo change upper bearings. How to...
  6. Franco_boater

    Yoke seal

    @achris... can You tell me how to dissasemble the whole set? I need to change my bearings one is rusted.... can you mark on the picture please step by step from which side use the pry tool/separator to dissasemble it please, thanks Spacer number #21, is it important which side facing gear/unis...
  7. Franco_boater

    Yoke seal

    Si si, I mean outer. thanks for clarifying.... I will post updates...
  8. Franco_boater

    Yoke seal

    Is it right when tight? I think its too tight but I dont know, will try while rolling torque, shouldn't it spin with ease? for example my driven gear on the shaft spins very easily, without any ressistance but the Yoke gears and bearings are quite tight I dont know if its preload set too much...
  9. Franco_boater

    Yoke seal

    Is it right when tight? I think its too tight but I dont know, will try while rolling torque, shouldn't it spin with ease? for example my driven gear on the shaft spins very easily, without any ressistance but the Yoke gears and bearings are quite tight I dont know if its preload set too...
  10. Franco_boater

    Shift shaft bushing removal and install

    @achris my friend, last question to You... seal is with dual lip, but which side UP? Each side is slightly different\
  11. Franco_boater

    Yoke seal

    Thank You, how tight the bearings should be while spinning it in hand When removed from my Yoke it was quite tight...Take care
  12. Franco_boater

    Yoke seal

    Oh didn't know that... so 5.25lbinch is the limit and can be below that value or the final target torque value?
  13. Franco_boater

    Shift shaft bushing removal and install

    @achris I have a question to be 100% sure, I have installed my shift shaft bushing and seal facing UP (spring facing UP) towards U joint bellows, is that correct? so the exhaust side will be like this: And do You think I can use some socket to push/hammer the upper drive shaft seal? its 1...
  14. Franco_boater

    Yoke seal

    I am sorry... He posted this But I cant find this info in 14 manual... and my manual says only 5.25lb-in but above we have some range... why
  15. Franco_boater

    Yoke seal

    Can I reuse the nut from the gear set?
  16. Franco_boater

    Yoke seal

    Ok, before disassembly I will check rolling torque on existing set, then I will try to set a new one after smacking with plastic hammer. I found in some manual there is a range in torque but in my manual #14 it says only the limiting value which is 5.5 lb-in. (0.55 Nm) for used bearings], Also...
  17. Franco_boater

    Yoke seal

    Thank You all is now more clear for me, We have perfect seal, is that ok or should I buy blue silicone??
  18. Franco_boater

    Shift shaft bushing removal and install

    Southern part, Calabria! Do You have any tips when installing this seal ?
  19. Franco_boater

    Yoke seal

    Yes I have checked your video, its very good and resonable for me. 1. Question about light hit, how much hit is enough? How I can recognize the hit relased the pressure? I can try to find or rent this tool maybe? But hitting with copper hammer is easier but I am afraid how much hit is enough to...
  20. Franco_boater

    Shift shaft bushing removal and install

    Thank You, Come to Italy You have to try our pasta! Also Help with yoke seal will be appreciated in other thread
Top