Search results

  1. Franco_boater

    A1G2 decisions. Rebuild or replace?

    when I was hammering bearing I inserted the tool with disc but not bolted to the bar, then pulled out a little the bar from the coupler, inserted bigger pipe over the tool and hammered the pipe which pushed the disk with bearing . Works perfectly
  2. Franco_boater

    A1G2 decisions. Rebuild or replace?

    I think you need to slide back 1/4” off towards small end Then make a hole you make this toavoid damaging the splines When hammering the gimbal, so the bearing stops at the race and the tool doesn’t touch the splines….
  3. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    Chris, I dont have loctite 222, only blue one or the red :) or perfect seal Do You think its safe to use blue or perfect seal or better to buy 222 /purple threadlock?
  4. Franco_boater

    A1G2 decisions. Rebuild or replace?

    Im wondering how ?? I tought its safe tool, maybe he didnt displaced the disk so it dont touch the splines when hammering....
  5. Franco_boater

    A1G2 decisions. Rebuild or replace?

    Scott06 you say this install tooll disc mounted on the tool is a wrong one??
  6. Franco_boater

    Gasket under Anode A1Gen2

    Hello boaters, I have a question, Ive got 2005 Alpha One Gen 2 and every year I remove anodes and clean them, now Ive noticed gasket under the anode but i dont have it. Do I need it? Whats for??
  7. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    Ok good night here its early evening, Ive found #37 is for V8 only but Ive got V6 with Dry joints, wondering why
  8. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    I will Thank you for your help. I have manual only for V6 engines @achris can You please post a pages from this manual
  9. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    When You go to parts catalog, here is the picture: and there, you see the gasket with restrictor hole towards the back of the boat, but on this picture: it says: Restrictor hole always opposite of the exhaust riser
  10. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    Thanks AChris for screenshot but i understand this seawater inlet should I put it as on the diagram ? But here it says this
  11. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    Do you Put something on the threads something ?
  12. Franco_boater

    Manfiold and elbow gasket replacement / torque and bolt question

    Hello boaters, During the winter I have inspected and repainted my manifolds + elbows. It looks fine, my question is, after torquening the bolts should i re-torque them after 1st boating? I cannot find this info and also I cannot find torque values for manifold and elbows.. I have also new...
  13. Franco_boater

    Shift shaft bushing removal and install

    Hello Chris again, in manual 6 it says lip facing down, in manual for alpha 1 gen 2 it only drawing like this:… So what’s the correct? I installed both with spring up like this
  14. Franco_boater

    Bellows inspection check what do You think

    Thank You so you have experience with that? Is it common problem or just my boat has issue? That’s quite serious i guess
  15. Franco_boater

    Bellows inspection check what do You think

    Hello Before every season I’m inspecting my bellows, after last season I’ve found something like that; is this groove normal ? I’m also missing clip on the cable bellow because it was rusted (Last pic) Can i use regular zip tie? My boat is in the water during the summer Ciao
  16. Franco_boater

    Mercruiser 4.3L TKS Carb scan tool?

    Hello Achris, unfortunately I am on the other side of the Globe ;) But I have found some info about this adapter and found a mechanic with Rinda but they have PC Version, will it work? What do You think? That would be awesome to check real hours on my boat im so excited.
  17. Franco_boater

    Mercruiser 4.3L TKS Carb scan tool?

    Thats awesome but its so pricey for regular DIYer... better spend 700$ on fuel or for maintanance ;) @achris tell me what cable I need for TBV ?? Take care And there is no dealer / tech with this scanner in my area
  18. Franco_boater

    Mercruiser 4.3L TKS Carb scan tool?

    I have timing lamp for timing and for RPM ive used laser meter @achris that would be awesome to figure out my engine hourse, because Ive bought a boat with aftermarket tachometer so Im curious of the hours on my engine... Do You know if this software is avaiable for DIYer? What cable I will...
  19. Franco_boater

    Mercruiser 4.3L TKS Carb scan tool?

    Ciao, I have got 2005 Merc 4.3L V6 and I would like to ask You if this engine requires any scan tool? To check RPMS, oil pressure, how the timing works etc? I believe its TB V.
  20. Franco_boater

    Impeller base gasket Alpha One Gen 2 question

    When I was replacing impeller 1st time, I had plate with 2 gaskets already attached, but 3 years ago bought new OEM impeller with set like on pic # 1
Top