Search results

  1. ljc1957

    Prop Depth

    Is there any rule about how far below the bottom of the transom the prop should run in the water? I'm replacing the transom in my 14' runabout and I have the opportunity to increase the top side of my transom by 3". Of course, this raises the engine/prop 3". Would that have an impact on...
  2. ljc1957

    Transom Time

    I've put it off long enough. I've been reading threads on this site and I still have questions about this job. So far, i got the engine off and the splashwell out with little difficulty. I just started removing the old transom and, as you can see, it's soaked. Also, it was only 1" thick...
  3. ljc1957

    Trailer Paint

    I just finished painting my trailer with rusoleum oil based primer and paint. How long should I let it dry or sit until I put it in the water? Thanks
  4. ljc1957

    50 hp Seaking

    I've got a 1966, 50hp Seaking and it runs great. However, sometimes if I pump the fuel line too much, it floods the engine and I have to clean the plugs to get it to start. Also, after I'm done running it, I will tilt the engine up to put the boat on the trailer. When I do this, fuel runs out...
  5. ljc1957

    Trolling motor?

    Can you guys give me some advice on buying an electric trolling motor for my boat? I've got a 14 fiberglass boat that weighs approximately 500 lbs. I want an electric motor so I can access some small lakes that don't allow gas engines. Are used motors a good way to go? Thanks in advance.
  6. ljc1957

    Increase Idle Speed

    Can anyone tell me how to increase the idle speed on my 1966, 50 hp Seaking outboard? Is there simply an idle adjustment like on a car? Thanks
  7. ljc1957

    Fuel Leak

    I've got a 1966 Seaking 50 hp and tonight when I lifted the motor I noticed gas dripping slowly from the cowling. It was dark and I grabbed my flashlight and removed the cowling. The leak was coming from the carb but I couldn't tell exactly where it was dripping from. I'll take a good look...
  8. ljc1957

    Just Wondering

    I've got a boat that I'm going through and I've spent a lot of time reading post on this site, which is awsome! I've learned that once wood get's wet, rot is inevitable. My question is, why did the manufacturers design and build boats knowing this fact? Just wondering.
  9. ljc1957

    1966 Seaking 50 hp

    Is there a way to tell who manufactured this specific engine for Montgomery Wards? The model number is: VWB 1909 1a Serial number: 10019 Thanks
  10. ljc1957

    Paint Question

    I'm looking at different paints and I'm trying to figure out what the difference is between the marine Rustoleum and the Briteside, Interlux paints. The latter two brands are about 3 times the cost of the Rustoleum. I don't think the Rustoleum is a polyurethane. Is that important? Are the...
  11. ljc1957

    Transom Test

    I took the advice of this forum and I drilled a couple of test holes part way into the transom looking for rot. The shavings came out dry but they were very dark colored. I was hoping they would be white in color but at least they were dry. The wood on the surface of the holes were soft...
  12. ljc1957

    Engine Question

    I was out on the lake today having fun with my new project and I decided to remove the engine cowling. I drove the boat without the cowling and I could have sworn the motor ran a lot smoother. The only thing I can figure is that my carb could be a little too rich. By the way, how does a good...
  13. ljc1957

    Engine question

    I have a 50 hp, 1966 Seaking OB. It runs great but when I shut it off, it shakes violently almost like it's dieseling. Could it be something else?
  14. ljc1957

    Transom Question

    I just bought this 48 year old boat knowing I was going to have to replace the transom and the floor. There are a couple of quarter sized soft spots on the inside of the transom. My question is: should I use the boat for the rest of the season? The previous owner used it regularly for the...
  15. ljc1957

    Engine Mounting Question

    I just bought a 1963, 14' boat with a 1966, 55 hp Seaking outboard. I was looking at it today and noticed that it has clamp mounts that go over the transom and it has 2 bolt mounts that sit under the waterline. Anyway, the motor is held in place with only the top clamp mounts. There are no...
  16. ljc1957

    New Project

    I went and looked at the boat and bought it for $800. During the test run the engine performed flawlessly. The hull has a small soft spot under the driver's seat and the transom seemed solid. No cracks and I attempted to move it with the engine up. No cracks or soft spots in the hull. I...
  17. ljc1957

    1966 Sea King 50 hp

    Well, I went and looked at the boat and took it for a test drive. I couldn't believe how well that old engine ran. Can you guys give me some imput on this engine. Also, is this a water cooled engine? I couldn't see the stream of water coming out of the back. I read somewhere that some of...
  18. ljc1957

    What do you think?

    I'm going to look at this boat tomorrow and I think the seller is motivated. I really like the lines of this boat and I was wondering if you guys think it's possible that the transom and flooring are still in good shape? The owner claims it was run in fresh water only and that he is the...
  19. ljc1957

    Westbend/Chrysler worth it?

    I,m getting ready to look at this boat and I really like the hull design. Anyway, with help from this forum, I've figured out that the outboard on it is a 60's Westbend/Chrysler, 40hp outboard. The owner claims it runs excellant and will push the boat to almost 30mph. My question for you guys...
  20. ljc1957

    Help with Identification

    Can you guys tell me what make and maybe what year this 40hp outboard is? The boat is a 63 Dorsett. Thanks
Top