Search results

  1. crankbait cowboy

    1973 starcraft ss restore in progress

    Some more progress, I am now working on spar varnish and carpet for a front pedestal up in bow, and back seat area ( still working on a plan as I go for seat
  2. crankbait cowboy

    1973 starcraft ss restore in progress

    I believe I have it all wired up and all works as should. I actually used 2 wiring diagrams off the web, if anybody can find them useful. I certainly did
  3. crankbait cowboy

    1973 starcraft ss restore in progress

    Now, onto starboard wiring
  4. crankbait cowboy

    1973 starcraft ss restore in progress

    A bit more progress Got port side wires strung thru the lower bow area, ran a drain hose from tanks to bilge area behind the side panels, insulated around tanks , and buttoned up bow ( still have some wiring in upper bow area for nav light)
  5. crankbait cowboy

    1973 starcraft ss restore in progress

    Also earlier I mentioned being lucky with good patterns from old
  6. crankbait cowboy

    1973 starcraft ss restore in progress

    And more
  7. crankbait cowboy

    1973 starcraft ss restore in progress

    Some pics
  8. crankbait cowboy

    1973 starcraft ss restore in progress

    Got the front 3 pieces carpeted, and waiting for hatch covers Started the top vinyl bow rails Did some relief cuts with skill saw to help with the bend
  9. crankbait cowboy

    2024 Starcraft Splash of the Year Champion!

    Congrads!!
  10. crankbait cowboy

    1973 starcraft ss restore in progress

    Just got some spar varnish on the other side (2coats) The spar goes on much nicer and actually soaks in better, where the 2 part epoxy is more of a coating Both seem to do the job, but the spar was easier to work with ( no 2 part mixing and brushes on nicely . Now to get carpet on
  11. crankbait cowboy

    1973 starcraft ss restore in progress

    My tanks will be ice boxes ( no live wells) for a couple reasons. 1 cheaper and easier 2 . years ago, we just put the fish on ice till end of day, and I actually think they were easier to clean and far less slimy and firmer than in a warm livewell all day. One will be for fish, the other for...
  12. crankbait cowboy

    1973 starcraft ss restore in progress

    Fit em, marked em, put elbows on to drain, and added some insulation ( and floatation ) Will it help both causes? It can’t hurt was my thinking
  13. crankbait cowboy

    1973 starcraft ss restore in progress

    While drying epoxy, I fitted a couple of implement tanks I’ve had for some time and they fit beautifully ( luck sometimes is a wonderful thing)
  14. crankbait cowboy

    1973 starcraft ss restore in progress

    So then today I measured and cut hatch openings, and put a second coat epoxy on same side with a good dose on all edges
  15. crankbait cowboy

    1973 starcraft ss restore in progress

    I meant heat shrink tape. Next I cut my bow 3 pieces ( I was lucky and used old as templates ) using 3/4 marine plywood. In and out of boat a couple times to fit it, and put a coat of 2 part epoxy on one side. This is where I realized I hadn’t cut the 3 hatch holes.
  16. crankbait cowboy

    1973 starcraft ss restore in progress

    I used a solder iron for the soldering with connectors when possible and shrink wrap I got the dashes and front consoles installed along with front bow brace
  17. crankbait cowboy

    1973 starcraft ss restore in progress

    Got the bow frame done and dashes wired Now to install dashes/install console fronts/ install bow frame, before cutting bow seating and laying out bow area
  18. crankbait cowboy

    1973 starcraft ss restore in progress

    Sounds good h20, thanks
  19. crankbait cowboy

    1973 starcraft ss restore in progress

    I believe when I run out of the clarkcraft 2 part epoxy I will switch to the helmsman spar. ( I will have a bit of the bow and the stern area left of wood work.
  20. crankbait cowboy

    1973 starcraft ss restore in progress

    Thanks fellas I’ve been working on the front of consoles 2coats of Clarkcraft 2 part epoxy (4 on edges) And I will carpet both sides with Henry’s 663 and stainless staples
Top