Search results

  1. A

    1968 6 HP Evinrude need help

    Disassembled carb, removed aluminum plugs, soaked in Pine Sol for a day, washed with Carb cleaner, blew air. All new carb rebuild kit. New fuel lines. Filled dent on cam follower with JBWeld. Same problems. Thinking of ordering new coils and condensers just for the sake of trying...
  2. A

    First Tohatsu motor 9.9HP

    Not sure what you mean, most of my motors have points (old boys). Can you clarify? Tnx. Also, if it is dead, is there any option to get something that can replace it?
  3. A

    First Tohatsu motor 9.9HP

    Another thing: After I removed all the "protective" electric tape from the wires I see 2 wire end sticking from under plate. What can it be?
  4. A

    First Tohatsu motor 9.9HP

    I am back to this little guy and coil test showed required 0.3 Ohm on primary wiring and no continuity on both secondary wirings. This is kind of strange. So far all bad coils I saw had shortened wirings with no or very little resistance , but not "no continuity'. Am I doing it right? I am...
  5. A

    First Tohatsu motor 9.9HP

    Can I use these values?
  6. A

    First Tohatsu motor 9.9HP

    Finally got the manual that looks exactly the same, but it only mentions C and D models. Can I go by that for B?
  7. A

    1968 6 HP Evinrude need help

    Found this old thread. https://forums.iboats.com/threads/6hp-fisherman-need-help-with-cam-follower-adjustment-and-tiller-throttle-setting.578214/ Same motor, practically same issues. My Cam follower has the same dent. Ordered carb rebuild kit, so will post how it worked.
  8. A

    1968 6 HP Evinrude need help

    Tnx.
  9. A

    1968 6 HP Evinrude need help

    I got one very neat tool from old welder to clean orifices from microscopic size to 1mm. Always use it. It is great. I have learned about this small side hole you are talking about on one of my od OMC motors the hard way. It was driving me crazy until I figured it. Now I always check for one...
  10. A

    1968 6 HP Evinrude need help

    Just to clarify in case it did not sound well: I meant more experience than me. I am very amateur motor guy.
  11. A

    1968 6 HP Evinrude need help

    I know what you are talking about. I cleaned carbs on newer motors that were packed with "kaka". But this carb looked clean and fresh when I opened it. I did carb cleaned , blow air , all the things ,but just as the routine. There was nothing visible to clean. As I said - very clean , well...
  12. A

    1968 6 HP Evinrude need help

    1. Not sure about HS needle. Got it like that. 1967 Johnson has fixed HS jet. It will cost t about $30 to convert it back to fixed, do you think it is worth it? Or I can just keep HS needle closed. 2. I did not use spark tester , just took sparks out and observed the sparks. I just recalled...
  13. A

    1968 6 HP Evinrude need help

    I only use non-ethanol gas for my outboards and it is fresh. I do have 1997 6HP Johnson (same motor really) that I restored years ago and it runs perfectly. So, I am familiar with this motors. I could try to swap carbs , but Johnson is a kicker on my pontoon now, so I do not want to mess with it...
  14. A

    1968 6 HP Evinrude need help

    Hi, Trying to bring this motor back to use and could use some help. Model 6802R. Compression 140/138. Checked points to 0.02 and then when it was running I checked with strobe light. It stays perfectly between two marks on both cyls. Disassembled and cleaned carb. Opened low speed needle to...
  15. A

    First Tohatsu motor 9.9HP

    Not sure what red cord and switch... Is there a way to test the ignition coil with Ohm meter before I buy new one? I have done it wit OMC coils. Still do not have the manual for this motor...
  16. A

    First Tohatsu motor 9.9HP

    Tried it. Did not help.
  17. A

    First Tohatsu motor 9.9HP

    Finally got the plugs and fuel connector. Gave a few pulls,: no signs of life. Pulled out sparks and grounded them, pulled cord - no sparks. Needs new coil? Boats.net shows them still available for $52. What else could it be? Still waiting on service manual to be delivered.
  18. A

    First Tohatsu motor 9.9HP

    tnx
  19. A

    First Tohatsu motor 9.9HP

    Do you have a link to it? tnx
  20. A

    First Tohatsu motor 9.9HP

    I got it very cheap because owner stripped one of the plug's thread and did not want to bother with it. I put thread inserts on two of my OMC motors, so I know how to fix it, but I do not think I have to do it because I run thread chaser on it and plug sits tight now. The compression is 140 and...
Top