Search results

  1. dlogvine

    1993 Mercruiser 4.3 by rear main seal

    I did a rebuild on this engine and the rear main seal send in the kit was from a Ford motor. So I bought one at the auto store for a similar Chevy engine. Now it looks like there is an oil leak in that area. I wonder if the seals could be different, marine from automotive. And the other question...
  2. dlogvine

    1994 Mercruiser 3.0 fuel filter change. Broken screw

    I tried to replace the fuel filter in the 1994 Mercruiser 3.0l engine. It is housed inside the internal fuel pump housing. To remove it I needed to unscrew the holding bracket and replace the filter. However, when I tried to remove the screw it was rusted in and broke. Should I remove the fuel...
  3. dlogvine

    Replacing old carpet

    I am finishing restoration of my 1993 Bayliner Capri. Almost everything is finished. However the floor carpet that i installed at the edges looks not very professional and a little uneven which is more visual because i kept the old wall carpet. Is there a good link with visuals on how to make...
  4. dlogvine

    Fibergalssing the deck

    I'm going to replace the deck on my 1994 Maxum boat. I removed the old deck and going to cut the replacement plywood tomorrow. I'm planning to cover it with fiberglass on both sides and then use the cloth on the top and cover all the holes if I drill any with fiberglass before putting the...
  5. dlogvine

    1994 Mercruiser 3.0 running smoothly but dies on neutral or low gear

    I am working on my 1994 Maxum with 1994 Mercruiser 3.0 two barrel carb. It is running smoothly when a little gas is added by pushing the throttle but starts choking when Im switching to low gear and dies on neutral. I looked at the carb, Mercarb, and used some carburetor cleaner. It looks...
  6. dlogvine

    Oil leaking through the oil sensor.

    I purchased a new oil sensor for my 1993 mercruiser 4.3 v6. I used teflon tape when I screwed it in. When I turned the engine I notice a significant leak in the engine compartment. I looked for the source of the leak and found out that it is coming from the oil sensor. Could it be a bad sensor...
  7. dlogvine

    Any way to lift the boat?

    I took my project boat to the lake today. Second time was much better than the first, however, there were several setbacks. The throttle lever clutch button was stuck and it was kicking like a horse when I shifted. Will take the throttle lever apart tomorrow. The Second problem was with the...
  8. dlogvine

    1993 Mercruiser 4.3 v6 valve fine tunning

    I rebuild and assembled 1993 Mercruiser 4.3 v6 engine on my Bayliner Capri. Of course I forgot to adjust the rockers and fine tune the valves when it was easy and the engine was out of the boat. Now I had to do this after all was assembled and I had to adjust the rockers by the sound. I...
  9. dlogvine

    1993 Mercruiser v6 4.3 oil pan repair

    While installing rebuilt engine into the boat the engine was dropped from the stand and landed on the oil pan causing it to leak. I replaced the oil pan, however was interested in fixing the old one. First i managed to straighten the dent around the plug. But there was a significant leak in...
  10. dlogvine

    Quicksilver throttle control diagram

    While upholstering the side panels on 1993 Bayliner Capri 185, I removed the throttle control unit and removed the back panel. When assembled, the control did not function properly and is working in reverse order, when lever is pushed forward the linkage is closing the carburetor pump and vice...
  11. dlogvine

    1993 Mercruiser v6 4.3 carburator.

    I'm finishing this engine rebuild, but encountered a problem. Original engine had a quad barrel carburetor (Weber was inside when i bought the boat). However this carburetor was shut and seized completely and beyond repair. So i bought another marine carburator matching the intake manifold. This...
  12. dlogvine

    1993 Bayliner 1850 Capri gauges access

    I am working on restoration of 1993 Bayliner 1850 Capri boat. Couple of the gauges have broken retainer clips, but when I tried to remove the gauges I realized that the shelf under the dash panel does not allow me to reach the gauges and pretty much everything else on the dashboard. The shelf is...
  13. dlogvine

    using automotive spark plug wires on 1993 mercruiser 4.3 v6

    I looked to replace the spark plugs and spark plug wires on my rebuild mercruiser v6. The prices for marine spark plug wires are twice the price of automotive, so I wondered if I can use chevy v6 4.3 spark plug wires instead of marine ones?
  14. dlogvine

    K&N automotive high flow oil filter in Mercruiser 5.0 v8

    I changed oil in my 1998 Mercruiser 5.0 v8. I thought I had extra oil filters available, but could not find any. Since all marine stores were closed at the time I went to an auto store and the other only filter that was matching the engine with high flow was K&N filter, high flow and high...
  15. dlogvine

    Mercruiser 5.0 alternator 55AMP vs. High 120-130AMP

    Alternator on my 1998 Ebtide boat went bad, could be from getting submerged under water for a short period of time, when the drain plug was not tightened up completely, letting the water into the engine compartment. I'm planning on taking out the old alternator and first checking it out and if...
  16. dlogvine

    Damaged oil pan 1993 Mercruiser 4.3 v6 non vortec

    I was ready to drop in the completely assembled Mercruiser 4.3 v6 into my boat. The engine fall from the hoist and the oil pan got damaged. It banged on the oil pan bolt. The bottom of the pan was a little dented and the corner where the drain plug is was dented more and the oil plug started...
  17. dlogvine

    boat cover maintenance and protection in Arizona

    I leave in Phoenix area in Arizona. My boats and jetski are all stored in ouside storagewith no sun shade or rain cover. After just a year even more expensive boat covers deteriorate and get nonelastic. This sun damage is enhanced by some rains and i have to either patch the covers with a lot of...
  18. dlogvine

    Mercruiser 4.3 v6 installed accessories pictures

    I am putting together 1993 Mercruiser 4.3 v6. Unfortunately, I could not for my life's sake find the pictures of the engine I made before taking it apart, and also I have a good idea as to where do the fuel pump, coil, fuel filter and other small accessories go, I want to make sure I'm putting...
  19. dlogvine

    Harmonic balancer installation

    How far should the harmonic balancer be sitting on the crankshaft? Im afraid to strip the thread but also concerned about harmonic balancer not sitting too tight. There is about a 1/4" gap between the balancer and timing gear cover. I'll post pics tomorrow. Thx
  20. dlogvine

    1993 mercruiser 4.3 v6 dipstick pipe pressfit

    Just wondered how to put the dipstick pipe in the engine. I cleaned the ring and the hole in the block with the cleaning brush cloth(forgot how it is called), then oiled both and tried to pressfit it in. Does the ring have to go inside the block or it is the tying bolt that keeps this pipe in? I...
Top