Search results

  1. H

    Ji'had?

    <br /><br />c/6<br /><br />Hooty
  2. H

    M.O.A.B.*

    *Mother Of All Bombs<br /><br /> <br /><br />c/6<br /><br />Hooty
  3. H

    PRICELESS !

    <br /><br />c/6<br /><br />Hooty
  4. H

    Next In Our How-To Series- - - Hip Replacement

    <br /><br />c/6<br /><br />Hooty
  5. H

    Jetting Two Cycle Outboard Engines

    There are frequently questions asked about the proper jet or orfice sizes for different outboard engine carburetors.Below is a post about this from a different board. Jay Smith, the guy who wrote the post, owns Jay Smith Racing Engines in Dayton, Texas, between Houston and Beaumont. He's a real...
  6. H

    Non-contact Infrared Thermometer

    I know these have been around for quite a while but recently the prices have dropped to the point they are affordable,like a 100 bux. I don' have one yet but there's one in my future. It appears to me that with this, you can not only tell if an engine is running hot or cold but by aiming it at...
  7. H

    USS Cole Recovery

    I thought this was interesting. Some of ya'll may too.<br /><br /> http://www.pianoladynancy.com/recovery_usscole.htm <br /><br />c/6<br /><br />Hooty
  8. H

    Bad Day At The Office?

    Here's ah bad day at the office!<br /><br /> http://home.attbi.com/~jehart1/wsb/media/68666/site1032.jpg <br /><br />c/6<br /><br />Hooty
  9. H

    Comprehending Engineer's Minds

    I got this a coupla days ago and thought some of ya'll might find it funny.<br /><br />c/6<br /><br />Hooty<br /><br />COMPREHENDING ENGINEERS . . . <br />TAKE ONE<br />To the optimist, the glass is half full.<br />To the pessimist, the glass is half empty.<br />To the engineer, the glass is...
  10. H

    Moderator 1

    Maybe I'm missing something but what's the difference between Miloman offering to sell his 50hp Evinrude or parts of it and Trevor offering to sell a new prop or me offering to sell a carburetor bowl?<br /><br />c/6<br /><br />Hooty
  11. H

    Christmas Checkride

    Santa Claus, like all pilots, gets regular visits from the Federal Aviation Administration, and it was shortly before Christmas when the FAA examiner arrived.<br /><br />In preparation, Santa had the elves wash the sled and bathe all the reindeer. Santa got his logbook out and made sure all his...
  12. H

    Kroil

    Some of ya'll are familiar with this product, some are not. For those who don't know, it's the best penetrating oil and bore solvent I've ever used. I've been using it for a little under 100yrs. and it beats the other penetrating products hands down. You can't buy it in stores, you've gotta...
  13. H

    Speaking of duct tape...

    How about a thread on the various uses for duct tape ya'll have found over the years or weired things you've used it for. There's got to be a gazillion duct tape stories out there.<br /><br />One use I found recently is using it to back sand paper. It stops it from falling all apart.<br /><br...
  14. H

    Evinrude Carburetors And Boyesen Reeds

    I'm installing late model(3-5/8" bore)235hp carburetors and Boyesen reeds in my early model (3-12" bore)235hp Evinrude. I think Boyesen recommends increasing primary orfices 2 sizes. With the larger cid carbs, sholud it be necessary to change orfices?<br /><br />Thx. & c/6<br /><br />Hooty
  15. H

    Orfice Size For Leak-Down Test

    How do you determine what size orfice to use for different size(CDI)engines. Obviously a small orfice for a small engine larger for a larger engine. Any formula?<br /><br />c/6<br /><br />Hooty
  16. H

    Flywheel Hp. vs. Prop Hp.

    Another post prompted this one.<br />I know an old o/b wrench that sez the 10-15% horsepower loss figure we use between crankshaft and propshaft is b.s. He sites as an example,a 150hp engine vs. a 200hp engine powering the same l/u. At 10% loss the 150hp engine is only going to loose 15hp,but...
  17. H

    Test

    Maybe Hooty and the Katcando<br /><br />c/6<br /><br />Hooty
  18. H

    Rod Knocking & Thermomelt Stiks

    R.K.,<br />If ya would, lemme know how to get in touch with ya so I can order a coupla Thermomelt Stiks (125 deg. & 163 deg.)I'd sure appreciate it. When I talk about 'um around here, everybody thinks I've been smokin' castor beans or something.<br /><br />Thx & c/6<br /><br />Hooty
  19. H

    Timing On A Trailer

    The timing spec. for my '76 200hp 'rude is 28 degs. BTDC.<br />When using the Dhadley method of timing on a trailer, is it safe to set the timing at 28 degs. BTDC, or would you retard it a degree or so too 26 or 27 degs.?<br /><br />Thx. & c/6<br /><br />Hooty
  20. H

    ?? Where To Find ??

    My Evinrude manual sez to use 125 & 163 deg.f "Markal Thermomelt Stiks" to check engine temperature.<br />Anybody know where to find such thangs??<br /><br />c/6<br /><br />Hooty
Top