Search results

  1. demarko210

    New piston rings

    I installed new piston and rings in my Mercury 110 now when I try to turn the flywheel it's very difficult and almost ripped the pull starter out. Can anyone help and tell me where to look it's a Mercury 110 serial number 318 XXX thanks guys
  2. demarko210

    Transom Wood

    Can I use this wood at lowes for my transom on my 19ft gradywhite? I also wanted to know if I remove my floor with out popping the cap with my hull warp?
  3. demarko210

    115 inline again 531??? distribute-less

    I am having a problem getting my boat of the ramp now. When I shift into gear the engine slows and cuts off. I have been reading this forum and everyone says to adjust the idle mix screw with the engine in forward gear. I am not doubting what they say and I will try this method but how do i get...
  4. demarko210

    Switch assembly

    On tell me what the Mercury switch assembly is used for? Part # 87-33386A 3.
  5. demarko210

    115 inline 531??? fuel pump

    My question is about the fuel pump, in my diagram I have 5 pieces to the fuel pump the five pieces are two gaskets,diaphragmm,cover ,and the base. However on my engine I still have 3 other pieces which are one gasket then a metal plate and then another gasket is attached to the engine. my...
  6. demarko210

    Transom Replacement

    When I replace my transom I will be doing it from the inside of the boat. I wanted to know can it be replaced in 3 sections instead of one whole piece? I have a notch transom on a Grady White boat. I wanted to cut the transom in 3 and bond it back in place. Because of room restrictions the 3...
  7. demarko210

    1974 Grady Weekender Transom

    My transom is water logged. When I place my finger in the upper parts of the transom where the motor bracket and ladder rest, it is soaked with water. I also notice from the inside looking out in the same location I can see light making it way through. Is there anything I can do to as a...
  8. demarko210

    115 inline 531??? choke

    When I press the button at the ignition the choke closes but after the engine starts it stays close. It use to open back up after i depressed the key. Can anyone tell me where to look?
  9. demarko210

    Mercury 110 9.8 rebuild hone cylinder?

    I am doing a rebuild because of low compression. I am adding new upper and lower bearing and seals along with piston rings. I wanted to know after adding new rings to the pistons is it a need to hone the cylinder?
  10. demarko210

    carburetor jets for KB11A mercury 110 9.8hp 318XXX

    Can anyone tell me where I can find some carburetor jets for KB11A
  11. demarko210

    Stator Mercury 115 6cycl 5314656

    I replace the stator on my motor now the engine will hardly start and when it does it will not stay running. The stator had an extra ground wire which i told was normal. The color code of the wires do not match what is on my switch box. The switch box ask for red and blue on the top and the...
  12. demarko210

    Mercury 115 6cycl 5314656

    I replaced the stator because the wiring was shot. I replaced it with Sierra International 18-5854. Now when I runs there bad miss somewhere. I can not get it to run long enough to check with my timing light. I want to know the new stator had an extra black wire that me original did not have. I...
  13. demarko210

    Mercury 110 9.8 3183164

    This is a pull start motor with spark and new points adjusted to .02 is very hard to get running. My question is, when I did a compression check it came out 60 psi both cylinders. Is this acceptable for a pull start reading? Also it is very hard to pull. I replace the rewind spring. The motor...
  14. demarko210

    What size transom mount trolling motor for my boat?

    I have seen some pontoon boats and other 20ft vhull boats with electric trolling motors. I was wonder what size would i need for my boat? 19ft grady white mercury inline 6.
  15. demarko210

    Mercury 110 #3183164

    I can not get the motor to turn on the swivel. I added grease at the connector and it still doesn't not turn left or right. Do I need to replace something or heat it?
  16. demarko210

    Inline 6 serial 5314656

    On the port side at the bottom near cylinder 6 there is water spraying out. Can someone tell me the correct part or gasket to buy to fix this? My compression reading are 100 100 110 110 110 95 thanks. The entire cover where the throttle arm is will need to come off. Can someone tell me the name...
  17. demarko210

    Spark Plug to Coil

    I was changing my spark plug wires and i removed them all and cut some new ones. I forgot how they went back on and the picture that i taken its not clear. i wanted to ask you how does the spark plug wire line up from spark plug 1-6 to its respective coil 1-6? is it plug 1 to coil 1, plug 2 to...
  18. demarko210

    Mercury inline 6 wont idle

    My serial number is 5314656-5600966. Here is what i have done. clean fuel tank, new sending unit in tank, new fuel line, rebuilt carbs, rebuilt fuel pump, used rebuilt lower unit, and plugs. compression 95,95,100,100,110,95. is this ok??? I am in the process of rewiring the harness assembly...
  19. demarko210

    Upper Shift Shaft I6 115hp

    I have attached a picture of the item. the upper shift shaft that is connected to arm by a lock nut which entails moves the shifter cable along the guide. I replaced this lock nut with a new one and now when I tighten the nut the shifter from the control is impossible to move from F to N to R. I...
  20. demarko210

    battery terminal crossed by shop 115 mercury I6

    I am new to boating as of last July. I purchased a 19ft grady white weekender cc with a 115 hp inline 6 5314656. i took it to a repair shop near me. they clean the carbs, installed a new bilge pump, and did a boat inspection for me. Well after getting the all green i take it to the ramp and try...
View older results
Top