Search results

  1. Scott06

    Out drive water flow incorrect?

    its normal. If you look in where the water is coming out behind shift lever, there is a 1/4” hole. There should be a clip that holds the speedo tube in it. With drive up this is open to exhaust cavity which is where the wate4 is coming from
  2. Scott06

    How much water pressure is too much, for running on the hose?

    you must be close to the water tower. Do you get water hammer when the washing machine valve closes? Newer construction will have a reducing station in the house, but what you mention is pretty typical for public water. the 3 homes we have owned on city water have all had 75-90 psi .
  3. Scott06

    How much water pressure is too much, for running on the hose?

    I wouldn’t worry about it any excess will blow out the muffs
  4. Scott06

    Alpha 1 Gen 2 - leak & transom service questions

    if the Y pipe was leaking and you stick a hose in bellhousing the water should go through the engine and leak out the Y pipe, engine running or not. I think the places above the Y pipe that could leak are driveshaft bellows, water in pipe fitting, steering shaft seal. Not sure if shift bellows...
  5. Scott06

    No Spark – 1998 MerCruiser 5.7L Thunderbolt V Ignition

    A lot of folks will use a Delco EST to replace the complete TB system when the module dies due to TB module cost/ lack of availability. The Delco is an OEM quality system and modules when they die are cheaper, although we have seen folks on here getting bad EST modules or having trouble putting...
  6. Scott06

    No Spark – 1998 MerCruiser 5.7L Thunderbolt V Ignition

    in addition to testing above. A bravo module is not made to work with a shift interrupt, so i dont think it will go out of gear. I test ran my engine when I repowered with a bravo module (alpha set up as well. If I recall it worked with the bravo module with the shift interrupt wires from the...
  7. Scott06

    Should I use a kicker when trolling in a 4.3L Mercruiser?

    you are already on the lower side of pitch with a 17". the only thing you may want to keep an eye on is wear on the coupler, you can actually get more wear on the splines trolling as the solines load and unload due to wave action. Not saying this is a deal breaker just something to keep an eye...
  8. Scott06

    Aftermarket Mercruiser parts, What are you using???

    how so?
  9. Scott06

    The easiest and most precise way to install a gimbal bearing

    if they are beating on it the bearing is most likely cocked in the transom housing. Going in or out it shouldn't take that much force. The tolerance ring on the outside crushes a bit to hold it but shouldn't need anything than a good sized hammer to drive it in. Use the OEM bellows for...
  10. Scott06

    Alpha 1 Gen 2 shift shaft seal replacement

    I think it uses either the sleeve or the washer in this parts breakdown both are listed as part #34. you should be able to track it by your serial number, may be a minor change...
  11. Scott06

    Stalling, sudden low idle.

    negative side of coil sends signal to tach. Some mercs will have two grey wires on negative side of coil- one for tach one for ignition module. You can take off the one going to the the tach. Others will have only one wire that splits in the harness and and goes to Ignition module and tach, in...
  12. Scott06

    Water leak

    post a pic - by inside of gimbal housing are you talking about where the exhaust bellows go? or on inside of the boat ?
  13. Scott06

    I/O (Sterndrive) Conversion to Outboards

    You dont necessarily need to replace it pound for pound. Just need to lower tongue weight
  14. Scott06

    Aftermarket Mercruiser parts, What are you using???

    Use the OEM quicksilver/mercruiser. The originals on my biat lasted 18 years, why screw with anything else. They will fit and last. Get a factory manual for your OD as it takes you through the job step by step
  15. Scott06

    New engine installation

    Yeah that’s what happens when the spark coming off the coil has no where to go. That’s actually a good sign younhave a nice hot spark
  16. Scott06

    If you're wondering if your anti siphon valve is stuck, or clogged, here's a test....

    Agreed. My buddies boat had bogging issues this summer. Two years ago he was having this when pulling skiiers,I rebuilt the carb no issue for 2 summers, this year got progressively worse. we start working on it dump the fuel filter into a jar and in 5 mins it is a milky cloudy mess. was...
  17. Scott06

    Winterizing, use E-0 stabilized gas or install shut off valve and run carb out of fuel?

    It (carb) will dry out just sitting there. I put stabil in my tank starting Labor Day so it pulls through the system. I do this with both my boat (carb/ ethanol Free) and jetski (injected/ E10) never had an issue fuel wise with either, nor seen any chit in the fuel filters. Generally I fog but...
  18. Scott06

    Running New Style Merc 6.2L DTS on a Pallet ???

    That's what I figured , so it needs to come out anyways should be able to set it up for test firing
  19. Scott06

    Running New Style Merc 6.2L DTS on a Pallet ???

    If you have to remove the DTS rigging anyways that would be easiest to run it out of the boat. Or are you keeping it for use with merc outboards? or does it not work that easy...
  20. Scott06

    Gm 4.3 blocks

    the 090M (m for metric) has metric fasteners on the starter, flywheel cover, and side motor mount holes. Don't ask me why GM mixed metric and SAE on the same block I swapped a 090M 4.3 in my boat for a 5.0 that has all SAE fasteners- was no big deal about $45 worth of bolts. All the accessory...
Top