I have a 1973 rude 135 I'm trying to get going. It has a new power pack and 4 new coils. I'm chasing a spark issue so I put a inline test light and a gap tester on my plug wires with nothing showing. So just for fun I pulled out the spark plug and held it against the head to see if it would...
So last year I put away my 17ft sea sprite with a 1973 evinrude 135 without figuring out what was wrong with it. I had lost and sometimes had intermittent spark on 4 cylinders almost if it wasn't cranking fast enough. I was using a deep cycle battery to crank with. It ran fine earlier in the...
So I've been chasing issue after issue with this motor and haven't really been able to fix anything. The other day I was loading up to go fishing the night before. It started right up and idled with out the warm up lever. The next morning before I left I went to start it again and it wouldn't...
Last week took my boat out and it ran great. I put it in and after a min with the warm up lever up it started revving high like normal. Thwn I put it down and all was well. Today I put it in and it never really revved that high with that warm up lever and barley idled and eventually died I got...
Replaced a piston and rod bearing but that's it. I've ran it on muffs a few times probably a total of 30 min on 32:1 and pitted around on the water once for maybe 20 only about 2 gallons put through so far. I'm using quicksilver sythetic for my pre mix. Factory service manual says to use 50:1...
I got this 135 from a guy did some work on the motor which was missing alot of electronics but I have 76 85hp that had cooked postings from the p.o. well I got it all back together a month ago and it ran in the driveway just fine. Go to put it in water a week later and I get some bad smoke...
Went to get plugs for my 1973 johnson 135 today. I replaced my 85 power head with a 135 last year. The plugs in the 85hp were ql77jc4 the ones recommended are ul77v surface gap which no one has is there a difference do I need to run a surface gap in this 135 or will the ql77jc4 be ok also what...
I have a 73 135Hp ran it on muffs a week ago got kinda warm no big deal. I put it on the water this morning and I wouldn't start. Also this morning it was tilted all the way down as opposed to the being in the trailer bar last week. Also had fuel spitting out the carbs this morning pretty bad I...
Just rebuild carb yesterday revved up really good. Gave it back to the guy and he called and said it didnt wanna go past half throttle. Where to start besides the main jet cleaning possibly lean rich out of adjustment.? I said mess with the choke to see it runs better with choke
Had a friend drop off a 1980 johnson 4.5 Hp said he inherited it and it's sat for about 3 years all he did was replace spark plugs said he couldn't get it to start and he most definitely is not mechanically inclined so I'm gonna check for spark and clean the carbs. Question is if there's no...
Just got my power head put back together (73' 135hp) some of you might be fed up with all my posts but im on the cusp of having this old girl 100% i was running on muffs the other day for the first time and i noticed i could on hold my finger on the head for a few seconds. Thought that was a...
Just rebuilt the power head on my 73 135 evinrude. Started it up and it ran good water coming out of the pew hole but also coming out of the seam where the lower unit meets the midsection. Also water stopped coming out of the pew hole and it started to get hot. After 10 min the heads are almost...
1973 evinrude 135 I only replaced one piston the rest have good compression all above 120 service manual suggests 50:1but that's a 40 year old book so what's recommended now a days. I'm about to start it on muffs today or tomorrow