Re: can water pump be rebuilt???????
I checked the store but the one it shows as being on my motor doesnot look like the one I have....here is a few pics of mine
Boat&motor- 1986 21' bayliner capri-aq225e #cu56837.....
yesterday my waterpump locked up while out fishing.....pulled the pump housing off and the bearings just fell out, what was left of them.... the housing is in good shape....my question is can i rebuild it???? if so were can i get the...
Boat&motor- 1986 21' bayliner capri-aq225e #cu56837.....
yesterday my waterpump locked up while out fishing.....pulled the pump housing off and the bearings just fell out, what was left of them.... the housing is in good shape....my question is can i rebuild it???? if so were can i get the...
just bought a 1951 sea king 5hp..... 15gg-9015...ser#367677..... trying to get it going... does anyone know a place to get parts???? right now i need the friction spring for the pull start.... i have the parts catalog and owners guide....
Boat&motor- 1986 21' bayliner capri-aq225e #cu56837..... 305 with a quadrajet...
boat ran fine for the past 8 trips.... this last trip it ran good most of the day just fishing.. then i pulled the tube for about 5 minutes and it started acting up... sounded like it was starving for fuel so i got...
Boat&motor- 1986 21' bayliner capri-aq225e #cu56837.....
new carb, dist, dist cap, plugs, wires, rotor.... timing set at 8 degree btdc at 600rpm....
engine idles great at 700rpms.... put the boat in the water under a load and it runs fine up to 3000rpms then the secondaries open and it boggs...
engine aq225e....I pulled my engine to change the driveshaft bearings now I have the parts so I'll pull them in the bellhousing then put it back on the engine..... my question is does the engine need to be aligned???? if so how do I do it????
hello all... my outdrive makes crazy noises so i took it off and the u-joints were rubbing on the housing..... the drive shaft coming out has alot of play in it and the bearing(maybe a seal) that i can see is gone bent and torn.... so how do i replace it???? and fix the play in the driveshaft>???
hello all I have a volvo penta aq225 I changed the dizzy from a points system to a ready to run dizzy.... boat has been working great.... planned a tubing trip today so I started the boat lastnight just to make sure... cranked on the first turn of the key..... got to the boat ramp this morning...
Boat&motor- 1986 21' bayliner capri-aq225e #cu56837.....
first off the boat ran great form the past two weekends so took it out this weekend and it ran fine for the first 2 or 3 hrs then while running at 3/4 throtle it stalled out sound a like like it ran out of gas so i put 5 gallons of gas in...
Boat&motor- 1986 21' bayliner capri-aq225e #cu56837...275 outdrive....
my tilt switch is not on the throttle and and only has a lite that is on until the drive is all the way down it did not have a gauge.....I installed all new (7) gauges when I rebulit the dash and the new set has a trim/tilt...
Please help I'm at a loss here!!!!
Boat&motor- 1986 21' bayliner capri-aq225e #cu56837.....
ok the boat ran 2 months ago. i decided i was gonna pull out all the carpet and refinish the inside with no carpet, like i said boat ran the week before i started this project...i completed the project...
hi everyone! new to posting so hope I'm doing it right. I have a 1986 21' bayliner capri AQ225E. I had a starting issue figured out it was the points and coil.... changed the points condenser and coil already had new wires and plugs. got it to fire now but it just starts for about 3 to 5 seconds...