Recent content by gica

  1. G

    1990 Force 120HP carbs mix adjustment help

    So I set timing at 28BTDC. I tried adjusting the mix screws by the book but when I go counter clockwise I don't really get the bogging, stalling issue to go the other way until stalling again and adjust in the middle. So I read somewhere, maybe Jerry mentioned it somewhere don't remember, that...
  2. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Thanks but this has been fully rebuilt, machine shop, new pistons, rings all .20 oversized. I am at the broken carb tab, studder when running, bought another flywheel for good measure. When I took the old one off I heat it up and had to hammer it, so I don't know if the magnets were affected in...
  3. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Here is the piece. I don't think one bolt is enough. It holds the float. No real strength needed but some is good.
  4. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Yeah I thought so. I am not too worried about the needle closing properly as it is pushed in by a tab on the float. But the manner in which it canbe safely attached is another story.
  5. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    I guess I can give it a try. Any idea if the broken piece on mine can be reattached and if so what is the best way. Don't know if you can tig it.
  6. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    ok, I am getting over the flu here so brain fart, since the middle carb had no nozzle for the gas hose I confused it with a top carb, omitting the choke fitting entirely. Sorry about that so I guess I have 1 top and 2 bottom that I got newer. in the pics of the 3 it is like you said thanks for...
  7. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Here are the pics of the 4 carbs side by side. Left is my broken one. The numbers show 589061-1 on the 2 I bought and on mine 589061-3. Plus mine has tye TC-106A-994 also stamped. The other2 just have 086 or 104 stampe. Outside identical except for tye aforementioned changes, of tye air jet and...
  8. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Hey racerone how would you repair the broke tab? Take it to a welding shop? Or try using a rod and a Bernzomatic?
  9. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Mine is the first category. 90B The new older ones have the F589061 but don't know if the rest of the numbers are there. Tc106A I did not see for sure. Will check and show close up pics in the morning.
  10. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    This is cast aluminum, how would you safely do that? Is there a way to enforce the broken braket so I can add a pin too? And withstand gas.
  11. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    I was hoping that it'd work. The inlet needle looks shorter too. and it's all shiny metal no rubber. I hope the adjustment is the same for the air mixture screw.
  12. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Hi guys so one of the carbs, top one, had a mishap and a tab that holds the pin from the float broke off. So I bought what I thought was tye same carb. It was listed as F589061-1 TC106A TC-107A Force 1989-1994 Carb 120 125HP. But this thing doesn't have the same thing on top. The adjustment...
  13. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    That is a great idea thanks I replaced the trigger and the stator and am waiting to do the timing and start the motor up. Will update as soon as it's done.
  14. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    I could have sworn I already fixed it. I went one by one. Who knows why it was broken. I soldered all the wires then shrink-wrapped. Is tyere a test for the CD module? I did the voltage testing already. Posted it above. I am waiting for the Stator and I will go ahead and install it and the new...
  15. G

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Right I know but it does replace 300-F654029-1 and newer 4 wire 300-888797 that I have right now. So both should work on my 1990 Force 120hp. I don't have the CDI one . Anyways, I did find another broken wire from the CD module that goes tonumber one. It's the white and yellow wire, connector...
Top