Got my book today I am ready to go lol.
But I do have a question? I was looking at the carb float setting and the book says this - and to set it like this - I set my floats level like this level with the carb body Havent done anything to it today. Busy with other stuff around the house.
LOL,
My wife is gonna kill me (if she has to help me again time this dam thing) lol I just finished timing it to 15* since it is out of water. On the housing of the motor it calls for 19* BTC. I just put it all back together and attempted to start it and it still just cranks over and wont...
flyingscott,
I put the forward and reverse cable back into its holder and took out the throttle cable out of the holder so I can manually advance/pull/push this forward to set my timing at full speed, when it is hitting the screw with the rubber stop on it under the flywheel. I just need to...
LOL I was just gonna say it wont kickover when the throttle is in this position - What is this switch for? Here is how I grounded the spark plugs - And here where I will be making my adjustments - You did say to remove the throttle cable from its holder?
Flyingscott,
I now understand what you are talking about. As soon as I get stuff together today I will do exactely what you said to do! One thing to advance the throttle all the way I take that to mean push my shifter lever on the remote control stick forward? Also does this look correct...
Yes flyingscott, but to get to 15* I had to remove the blot and turn it to the right all the way in. I had both plugs out, wires inserted in there plug wire sockets and than grounded. I had the wife turn the key on the motor and had the timing light on the flywheel. I am thinking tomorrow to...
OK here is a better picture of the 2 areas I am looking at. The one screw above my pinky I say must be my timing screw? When I was setting my timing last night while turning this screw in or out either sped up or retarded my timing and the screw by my pointer finger is the cables coming from...
Help, guys just a few more steps and I think I will be good to go!
I've included several photo's to help me explain what I need help with. First all, thanks for everyone who has assisted me so far. And thanks in advance for anyone who might help me finish up my quest to have my boat out on...
"HELP" needed timing on my 1986 Tidecraft Evinrude 40HP VRO E40ELCDE motor???
I have a 1986 Tidecraft with a 1986 Evinrude VRO 40 hp E40ELCDE motor. I have replaced the VRO Pump due to dry-rotted diaphragms. I have rebuilt and cleaned the 2 carbs but now I am thinking now that it is out of...
I just hoguht of something could my timing be off on my motor? And if so what degree should it be set at for a 1986 E40ELCDE Evinrude? And how do you set it? I have youtubed it but still a little lost. I think picture #2 is where I would adjust my timing? And picture #3 is where I adjust my...
I think Figure #13 is the purple wire coming from the front of the boat and its wiring harness and #11 is the wire leading back to the VRO Fuel Pump? "A" is where the purple wire went into the the harness plug but on the opposite plug it is a blank spot, no connector.
Hi oldboat1,When the carb is upside down and the float is on top the float is exactly level with the carb's body.
Flyingscott I followed the instructions to the best of my ability last season and then took it to a local marina in Chicago and they went thru it and said they dont have the time...
I have a 1986 VRO Evinrude 40 HP E40ELCDE motor and am having trouble with it running. I replaced my 3 wire VRO fuel pump last year with a new 4 wire because the 3 wire pump was discontinued. I cleaned the carbs as well and changed out all my gas lines. The trouble is now my motor wont stay...