Search results

  1. D

    flywheel removal . can you lift and just turn engine

    got a 5.7 89 . i only have a car engine lift. boat has a rear wing. teeth are bad on flywheel. car i just lift engine spin it sideways . put on flywheel and reinstall. can it be done. 89 glastron w/ 5.7 alpha 1 . i think i got the room. but i am asking.. bob
  2. D

    labor on flywheel anyone

    on a 5.7 with alpha 1 . any mechanic know how much labor to replace the flywheel..motor and bolt on's are new. clean salt free motor bob
  3. D

    flywheel question 5.7 bad teeth...new one or just the ring gear

    i got a bad flywheel. would you remove it and just change the ring gear. or replace the whole flywheel.. bob
  4. D

    shimming a starter on a 5.7 89

    got a question my starter starts fine but dont seem to mess smooth. do you shim these starters on a 350 gm 89 . if so how. it a mini hi torqe one bob
  5. D

    where can i buy new oil lines for external oil filter

    where can i buy oil filter lines for external mounted oil filter that go from rear of motor to front oil filter . 2 of them 89 5,7 350 mag w/alpha 1 bob
  6. D

    oil consumtion on a rebuit 5.7

    should thier be loss of oil on a rebuilt 5.7 engine 1989.could it be blowing by as it only has between 5-10 hours on it ???
  7. D

    oem vrs aftermarket parts

    when you buy after market parts imo. like cap rotor etc. they are what they are aftermarket..manifolds are 1 thing but i got a new cap and dist with thunder iv new aftermarket dist. with after market rotor...piece of crap rotor fell apart after 1 full day out. so my advice on parts that matter...
  8. D

    timing and adjusting valves changes

    question if you adjust your valves, does it throw of your igintion timing. do you need to reset it..how about you carb mixtures. do they change with valve adjustments as the valves are closing and opening more... i am running good now . just need to know the answer bob
  9. D

    rebuilt motor valves tapping bad 5.7

    hi i got my 89 5.7 w/ alpha 1 running real good. good oil presure, went to take it out today second ride to break in motor. got it warmed up , the motor was tapping valves for sure. took it back to the dock and adjusted valves . sounded real good. went and got 1 more quart of oil , it sounded...
  10. D

    89 merc 5.7 alpha 1 thanks all

    i still have to replace exhaust bellows and change drive gears . but thanks all who helped me save my summer . i just timed the engine and am ready to break in my new engine..you guys kept me fighting. don.bondo.haut.coors supernova and many more thanks guys bob/philly
  11. D

    power steering pump 89 5.7 auto or boat

    i am finishing up all my little problem's now with my boat it an 89 5.7 w/alpha w/power steering. i looked at some boat sites for a power steering pump..is this one item thats a car pump???i got a leak in that little line in the back its cracked..i even tryed to slide the hose up over it to stop...
  12. D

    i messed up pulled risers not manifolds

    i messed up saying i pulled manifolds with out draining them but on a gm 5,7 it was the risers. do i still have to worry about water in clylinders??? bob
  13. D

    how to get water out of clys took manifolds off without draining

    got a different thread open but this is super inportant to me as i had to valves to tight and i rushed to take manifolds off..water will go into clys right??? i cranked engine over with all plugs out and started up for 5 seconds to get it running. please i need advice..this is a horror story for...
  14. D

    could someone give me a basic check list to troble shoot my engine

    hi all, i am in a jam. motor has no power 350 89 gm w/.alpha 1 the basic's only.. 1 compression 2 spark 3 timing can someone rewrite the basic to check all the basic things to rule out other things..i am going crazy over this boat. bob/philly
  15. D

    raker prop

    someone gave me a cleaver prop. ss. or my 5.7 23 pitch. what does a cleaver do.. bob
  16. D

    back to basic's starting over

    started a new post labeled it all wrong, boat still does not run right , found leak in coil wire , real bad fixed it with old wire same thing..i got appointment with a shop. but back to basics 1 compression test 2 can anyone give me more basic tests to preform?? checked timing ok.
  17. D

    small gash in my boat today

    above the water line i hit the end of the dock..and above the rub rail i put a gash 3"'s high and 5"'s long. and idea's how to repair it i laid fiberglass and can spray paint..any input would be great enclosed is a pict where damage is ..this is not the boat bob
  18. D

    change gas still runs bad

    well those that have been following my repair project thanks...i changed the gas i have a decent idle, while going for a ride it would not run above 10 mph 350 mag. 89 with alpha 1. i checked timing before and it was good..its a new motor rebuilt.. i found that a coil wire was bad and arcing...
  19. D

    water or dirt in fuel

    went for my first test run and i got water and dirt in fuel i have inline filter...emptyed it and it looked dirty...would not start till i messed with chock in water...hooked up clean outboard tank straight to fuel pump was able to get back to the dock. but it still ran bad. before all this i...
  20. D

    wrong drive install any advice wrong gearing 1.84-1 on v-8 350

    hi i poted this before i got a dealer who was to check and advise me before install the drive.. its and 1.84-1 drive i think from a 4 cly . i have an 89 merc . it needs 1.5-1 drive. i am ready for my water test today to check motor if all goes right. i will change drive soon. does any one know...
Top